Flywheel Housing - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 395-1592 | 吊耳组件 | 2 |
B | 8T-9022 | 硅胶密封垫 | - |
开始:
- 拆下曲轴后密封。
- 拆下电起动马达。
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 卸下将发动机油底壳固定在飞轮壳体 (2) 上的螺栓 (1)。
Show/hide table
图 2 g01058428 - 将工具 (A) 和适当的起吊设备安装在飞轮壳体 (2) 上。 飞轮壳 (2) 的重量约为
105 kg (230 lb) 。 - 拆下螺栓 (3 )。 将飞轮壳从缸体上拆下。
- 将密封垫 (4) 从飞轮壳上拆下。
Show/hide table
图 1 | g01008304 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 彻底清理飞轮壳和缸体的后端面。
Show/hide table
图 3 g01058428 - 将工具 (A) 和适当的起吊设备安装在飞轮壳体 (2) 上。 飞轮壳 (2) 的重量约为
105 kg (230 lb) 。 - 将密封垫 (4) 安装到缸体的定位销上。 在密封垫的底部涂敷工具 (B),填充缸体、飞轮壳体与发动机油底壳的空隙。
- 定位飞轮壳 (2) 后安装螺栓 (3)。
Show/hide table
图 4 g00551652 - 按照下列步骤拧紧螺栓:
- 按照数字顺序依次将螺栓 1 到螺栓 24 上紧到
40 ± 10 N·m (30 ± 7 lb ft) 的扭矩。 - 按照数字顺序重新依次拧紧螺栓 1 到螺栓 9 至扭矩为
135 ± 20 N·m (100 ± 15 lb ft) 。 - 按照数字顺序重新依次将螺栓 10 到螺栓 24 上紧到
55 ± 10 N·m (40 ± 7 lb ft) 的扭矩。
Show/hide table图 5 g01008304 - 按照数字顺序依次将螺栓 1 到螺栓 24 上紧到
- 安装将发动机油底壳固定在飞轮壳体 (2) 上的螺栓 (1)。
- 拆下工具 (A)。
结束:
- 安装电起动马达。
- 安装曲轴后密封。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Assemble
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Assemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C7.1 Marine Generator Set Generator Operation
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C7.1 Marine Generator Set Engine Operation
C18 Generator Set Safety Messages
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C7.1 Industrial Engine Electrical System
2013/06/13 New Fuel Lines Are Available on Certain C18 Marine Engines {1274}
C15 and C18 Engines for Caterpillar Built Machines Power Take-Off Drive Group - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Power Take-Off Drive Group - Assemble
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Gear Group (Front) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Housing (Front) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Rocker Arm - Assemble
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C7.1 Marine Generator Set System Pressure Release
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Remove and Install