Turbocharger - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | − | Henkel Corporation 抗咬合剂 (C5-A) | − |
- 松开卡箍组件 (1) 后断开连接到涡轮增压器(未显示)进气侧的软管。
- 拆下卡箍组件 (2) 和 (6)。 将软管组件 (5) 从废气旁通阀执行器上断开。
- 断开全部两条管组件 (3) 和 (4)。
Show/hide table
图 2 g01841575 - 拆下螺母 (8) 后丢弃螺母。 由两人拆下涡轮增压器 (7)。 涡轮增压器 (7) 的重量约为
31 kg (70 lb) 。 - 从排气歧管上拆卸密封垫。
Show/hide table
图 3 g02216274 注: 卡箍组件 (9) 为一次性使用部件。 一旦松动,废弃卡箍组件。
- 通过松开卡箍组件 (9) 将壳体从从芯组件上分离。 丢弃卡箍组件 (9)。
Show/hide table
图 1 | g01841534 |
典型示例 |
Show/hide table
注意 |
---|
不遵守下列规定程序可能导致零件损坏。 为了避免损坏零件,总是确认和标记零件,以便零件可以安装在相同的位置。 |
Show/hide table
波纹管的末端很锋利。 如果波纹管处理不妥当,可能会发生伤害。 通过波纹部位拿住波纹管。 |
注: 请参阅专门说明书, REHS1728, "波纹管应用指南",以了解机器上所配备波纹管处理方面的更多信息。
注: 确保所有主要表面清洁无碎屑。
- 按相反顺序安装涡轮增压器 (7)。
- 将新卡箍组件 (9) 上紧到
13.6 ± 1.2 N·m (120 ± 11 lb in) 的扭矩。 - 将工具 (A) 涂抹到螺柱和螺母 (8) 的螺纹上。 拧紧螺母 (8) 至扭矩为
70 ± 5 N·m (52 ± 4 lb ft) 。 - 将卡箍组件 (2) 拧紧至扭矩为
8.5 ± 2 N·m (75. ± 17 lb in) 。 - 把卡箍组件 (6) 拧紧至扭矩为
12 ± 4 N·m (106 ± 35 lb in) 。 - 把卡箍组件 (1) 拧紧至扭矩为
13.5 ± 1 N·m (119 ± 9 lb in) 。
- 将新卡箍组件 (9) 上紧到
注: 检查所有 O 形密封圈、密封垫和密封件有无磨损或损坏。 如有必要,请更换部件。
Show/hide table
注意 |
---|
波纹管的定位很重要。 不正确的定位会导致波纹管过早损坏。 目视检查波纹压缩是否一致,来判断是否定位好。 安装之前,检查波纹管是否有损伤。 如果波纹有任何损坏,废弃此波纹管。 波纹管口的微小破损可以修复。 然而,如果修理后安装有任何困难,废弃此波纹管。 |
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
Well Service Pumps Machine Operation
3512E Tier 4 Final Engines for Land Electric Drilling Oil Pressure Is Low
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Diagnostic Capabilities
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys DC Bus Capacitor - Replace
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Bearing (3.5 EVD or Greater) - Replace
C13 and C15 Generator Sets Generator Operation
C7.1 Industrial Engine Maintenance Interval Schedule
C4.4 Industrial Engine Welding on Engines with Electronic Controls
C6.6 Industrial Engine After Starting Engine
C4.4 Industrial Engine Cold Weather Starting
C175-16 Locomotive Engine Housing (Front)
Procedure to Troubleshoot All Refueling Pump Leaks on Certain Excavators{1295} Procedure to Troubleshoot All Refueling Pump Leaks on Certain Excavators{1295}
C13 and C15 Generator Sets Product Lifting
2013/07/01 New Flywheel Housing Assemblies and Gaskets Are Used on Certain 3500 Locomotives Engines {1157, 7555}
3512C Petroleum Engines with Dynamic Gas Blending Engine Control Switch - Test
C13 and C15 Generator Sets Product Installation
C15 and C18 Engines for Caterpillar Built Machines Air Control Valve - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Remove and Install
2014/06/20 J1939 Suspect Parameter Numbers for G3300B and CG137 Engines {1900, 1901, 1920}
C15 and C18 Engines for Caterpillar Built Machines Inlet Module (Catalyst) - Remove and Install
C13 and C15 Generator Sets Plate Locations and Film Locations
C7.1 Marine Generator Set Starting the Engine
C7.1 Marine Generator Set Starting with Jump Start Cables