Gear Group (Rear)
Show/hide table
Illustration 1 | g03201695 |
Show/hide table
Illustration 2 | g03201697 |
Vertical line |
Show/hide table
Illustration 3 | g03201698 |
Horizontal line |
Show/hide table
Specification for 112-5677 Rear Gear Gp | |||
Item | Qty | Part | Specification Description |
1 | 2 | 7E-3897 Camshaft Drive Gear | Before assembly, clean the taper of the camshaft and the tapered bore of the camshaft drive gear with lint free cloth saturated with cleaning solvent to remove excess oil. Clean with alcohol wipe. |
2 | 2 | 112-1554 Idler Gear As | After installation, bore of 125-9751 Bushing is Installation depth of the bushing is |
3 | 2 | 101-1368 Thrust Washer | Thickness of the new thrust washer is |
4 | 4 | 8M-2530 Bolt | Torque to |
5 | 1 | 4P-5437 Gear Shaft | Diameter is |
6 | 1 | 4P-5459 Balancer Gear Assembly | After installation, bore of 4P-5438 Bushing is Installation depth of the bushing is |
7 | 2 | 112-1552 Idler Shaft | Diameter is |
8 | 1 | 101-1365 Thrust Plate | thickness of the new thrust plate is |
9 | 2 | 9X-8887 Bolt | Use the following procedure in order to tighten the bolt for the camshaft drive gears: 1. Tighten bolt for the camshaft drive gear to 2. Mark a vertical line on the head of the bolt for the camshaft drive gear. Refer to Illustration 2. 3. Place a driver against the retaining plate of the camshaft drive gear. Strike the driver solidly with a hammer 3 to 4 times. 4. Again, tighten bolt for the camshaft drive gear to 5. Repeat steps 3 and 4 until the mark on bolt turns a minimum of 90 degrees. Refer to Illustration 3. |
10 | 4 | 1B-4367 Bolt | Torque to |
11 | 2 | 8S-2331 Bolt | Torque to |
Caterpillar Information System:
G3500 Engines Gear Group (Rear)
330F MHPU Mobile Hydraulic Power Unit Machine System Hydraulic Tank and Filter
C175-16 Locomotive Engine Fuel Transfer Pump - Install
G3516 Engines Accessory Drive (Lower Left Hand)
2012/12/06 A New Outlet Elbow Is Used with the Oil Cooler Adapter on Certain 3516B and 3516C Engines {1380}
G3500 Engines Cylinder Head Valves
C7.1 Marine Generator Set Control Panel - Marine Classification Society (MCS) Control Panel (If Equipped)
G3500 Engines Cylinder Head Valves
G3500 Engines Stub Shaft (Front)
G3500 Engines Gear Group (Rear)
3500 Industrial Engines Gear Group (Rear)
C32 Auxiliary Engine Starting the Engine
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Fuel System
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Air Inlet and Exhaust System
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Aftercooler
C175-16 Locomotive Engine High Pressure Fuel Rails - Remove and Install
C13 Tier 4 Final Engines Turbocharger - Inspect
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Electrical System
C7.1 Marine Generator Set Belt - Inspect
C7.1 Marine Generator Set Belt Tensioner - Check
C175-16 Locomotive Engine Flow Limiter - Remove and Install
C8.7 Marine Engines Inlet Manifold Pressure - Test
3500 Generator Sets with Dynamic Gas Blending Safety Messages
C175-16 Locomotive Engine Fuel Control Valve - Remove and Install - Primary