Symbols
Show/hide table
Grounding conductor for field wiring |
Show/hide table
Bonding point for internal bonding of equipment parts to ground |
Show/hide table
Caution. Refer to manual for more information. |
Show/hide table
Risk of electrical shock |
Show/hide table
Input |
Show/hide table
Output |
Show/hide table
Alternating Current |
Show/hide table
Phase |
Show/hide table
Neutral |
Show/hide table
Caution - See Service Manual |
Show/hide table
No Service |
Show/hide table
Read Service Manual |
Show/hide table
Not A Connection - This symbol indicates "Not A Connection" for a telecommunication network. |
Show/hide table
High Leakage Current - Earth connection essential before connecting the supply. |
Show/hide table
Lithium Battery - Danger of explosion if the battery is incorrectly replaced. Replace the battery with the same type of battery or replace the battery with an equivalent battery. Dispose of the batteries according to the manufactures instructions. |
Show/hide table
The heat sink or the bracket is not grounded. - Test before touching. |
Show/hide table
Safety Extra Low Voltage connections only. |
Show/hide table
Wait for 5 minutes before disconnecting all power sources before removing any covers or panels. |
Show/hide table
Illustration 1 | g00785184 |
Bypass Input |
Show/hide table
Illustration 2 | g00785185 |
The system is designed for services that have a 3-wire grounded wye configuration. |
Show/hide table
Illustration 3 | g00785207 |
The system is designed for services that have a delta configuration. |
Show/hide table
Illustration 4 | g00785208 |
The system is designed for services that are impedance grounded. |
Show/hide table
Illustration 5 | g00785210 |
The system is designed for services that have a 4-wire grounded wye configuration. |
Show/hide table
Illustration 6 | g00785212 |
The UPS receives power from multiple sources. |
Show/hide table
Illustration 7 | g00785215 |
Maintenance Bypass Switch |
Show/hide table
Illustration 8 | g00785216 |
Input Isolation Switch |
Show/hide table
Illustration 9 | g00785218 |
Output Isolation Switch |
Show/hide table
Illustration 10 | g00785222 |
"ON" Symbol |
Show/hide table
Illustration 11 | g00785223 |
OFF Symbol |
Caterpillar Information System:
UPS 250 and UPS 300 Uninterruptible Power Supplies Acronyms
C7.1 Industrial Engine Temperature Sensor (DPF Inlet)
2012/07/19 Water Pump Operation on C7.1, C6.6, and C4.4 Engines {1361}
3412 Generator Set Engines Cylinder Head Valves
C13, C15, and C18 Tier 4 Final Engines Air Inlet Elbow
C18 Marine Engine Engine Oil Sample - Obtain
CX48-P2300 Petroleum Transmission Power Train Electronic Control System General Information
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Connector Locations
C32 Marine Engines Closed Crankcase Ventilation (CCV) System
CEM Locomotive Aftertreatment Exhaust Outlet Nitrogen Oxide Sensor - Replace
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Service Tools
2012/07/13 A New Replacement Gas Regulator Is Available for G342, G343, G353, G379, G398, and G399 Engines {1000, 1270}
UPS 250 and UPS 300 Uninterruptible Power Supplies Operating Parameters - Set
794 AC Off-Highway Truck Final Drive Oil Level - Check
C7.1 Industrial Engine Temperature Sensor (Exhaust)
C7.1 Industrial Engine Injector (Diesel Exhaust Fluid)
C7.1 Industrial Engine Nitrogen Oxide Sensor
UPS 250 and UPS 300 Uninterruptible Power Supplies Getting Started
UPS 250 and UPS 300 Uninterruptible Power Supplies Menus
C32 Marine Engines Turbocharger - Inspect
UPS 250 and UPS 300 Uninterruptible Power Supplies Using Computer Software
Using the 223-2454 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI){0374, 0599, 0701, 0706, 1251, 1252, 1254} Using the 223-2454 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI){0374, 0599, 0701, 0706, 1251, 1252, 1254}
2012/10/04 A New Rocker Arm Assembly Is Used in Certain C11 and C13 Commercial Engines {1123}
C13 Tier 4 Final Engines Solenoid Valve