Counterweight Removal and Installation
标准机器配重的拆卸和安装
Show/hide table
机器的意外移动会引起人身伤亡。 为了避免机器移动, 应将液压锁定操纵杆移到锁定位置并在液压锁定操纵杆上挂上一个专门说明书, SEHS7332, "不准操作"的标签或相似的警告标签。 |
Show/hide table
在拆卸和安装配重块时如果配重块坠落,会引起人身伤亡。 拆卸和安装配重块时,禁止人员在其下方或附近逗留。 确保提吊设备状况良好,并且提升能力达到配重块的重量。 |
Show/hide table
吊绳上有负载时确保人员远离吊绳。 吊绳可能断裂,引起人身伤害。 |
配重拆卸
注: 拆卸配重前,断开后视摄像机的导线。 有关更详细的资料,请参阅 操作和保养手册, "摄像机线束 - 断开和连接"。
- 在坚硬平坦的地面上停放机器。 将作业机具降到地面。
- 把液压锁定操纵装置移到锁定位置。
- 从盖 (1) 上拆下五颗螺栓。
Show/hide table
图 1 | g02767757 |
- 打开盖 (1) 并将盖锁入打开位置。 盖在打开位置时用杆 (2) 支撑盖。
Show/hide table
图 2 | g02767836 |
- 用钩环将适当额定值的钢索固定在支架。 使用合适的起吊装置拉紧钢索。
Show/hide table
图 3 | g02767876 |
- 充分吊起配重,以使余下的螺栓空载。 如果钢索太紧的话,就很难拆下螺栓。 如果钢丝太松的话,就很难拆下螺栓。
- 拆下六颗配重安装螺栓和六个垫圈。
Show/hide table
图 4 | g02767917 |
- 从机器上分开配重。 将配重降到合适的支座上。
Show/hide table
图 5 | g01430966 |
配重安装
按相反的顺序进行安装步骤。
注: 暂时拧紧六颗配重安装螺栓。 降低起吊钢索的张力。 确保配重正确位于固定销上。 将螺栓拧紧至扭矩为 2700 ± 300 N·m (1990 ± 220 lb ft)。
注: 安装好配重后,重新连接后视摄像机导线。 有关更详细的资料,请参阅操作和保养手册, "摄像机线束 - 断开和连接"。
Caterpillar Information System:
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Swing Gear - Lubricate
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Swing Drive Oil Sample - Obtain
C175-16 and C175-20 Generator Set Engines Exhaust Has Excessive White Smoke
C175-16 and C175-20 Generator Set Engines Engine Cranks but Does Not Start
3516C Generator Set Engines Electronic Control Module (ECM)
2011/11/29 New Software Is Now Used on Certain C15 Generator Sets {1901, 1920}
1U-9600 Welding Group (U.S. and Canada) 1U-9601 Welding Group (All other countries){0599, 0679} 1U-9600 Welding Group (U.S. and Canada) 1U-9601 Welding Group (All other countries){0599, 0679}
2011/11/11 Changes Have Been Made to the Fuel System Diagnostic Service Tests for C9.3 Industrial Engines {1250}
C32 Marine Engine Refill Capacities
2014/01/27 Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
C11 and C13 Engines Exhaust Manifold
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Shipping the Machine
C15 and C18 Petroleum Generator Sets Circuit Breakers - Reset
3516C Generator Set Engines Restriction of Air Inlet and Exhaust
2011/11/11 New Software Enhances the Cylinder Cutout Feature on Certain 3516C Generator Set Engines {1901, 1920}
Procedure for Updating the C27 Engines in Certain O;K Shovel Excavators{1000} Procedure for Updating the C27 Engines in Certain O&K Shovel Excavators{1000}
2011/11/29 An Improved Oil Filter Assembly Cover Is Now Used on Certain C9 Marine Engines {1306, 1308}
C11 and C13 Petroleum Engines Maintenance Interval Schedule
Relay Inspection and Replacement on Certain Gensets{4460, 4493} Relay Inspection and Replacement on Certain Gensets{4460, 4493}
2011/11/11 Improved Alternator Guards Are Used on Certain C32 Engines {1154, 1405}
2011/11/18 Improved Seal Kits are Now Used on Certain Excavators {5456, 5457, 5458}
2012/02/06 The Lever for the Position of the Seat Cushion has been Improved on Certain Excavators {7312}
3516C Generator Sets Diesel Exhaust Fluid in Cold Weather
Updated Ride Control Accumulator Test and Charge Instructions{0738, 5004, 5077, 5081, 7474} Updated Ride Control Accumulator Test and Charge Instructions{0738, 5004, 5077, 5081, 7474}