Gear Pump (Torque Converter and Transmission) - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 350-4401     | Adapter Plate     | 1     |
B     | 4-34614     | Hoist Ring Columbus McKinnon Corporation     |
2     |
C     | 1U-9200     | Lever Puller Hoist     | 1     |
D     | 1U-5750     | Engine Stand     | 1     |
1P-2850 | Oil Drain Cart     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- If equipped with a rear PTO shaft, remove retaining ring (1), bearing assembly (3), and output shaft (4). Remove retaining ring (2) in order to remove bearing assembly (3) from output shaft (4) .
Show/hide table
Illustration 1 | g02377717 |
- Remove bracket (5) .
Show/hide table
Illustration 2 | g02454019 |
- Install Tooling (A) onto the transmission housing.
Show/hide table
Illustration 3 | g02377316 |
- Use Tooling (B), Tooling (C), and a suitable lifting device in order to install transmission and torque converter (6) onto Tooling (D). The weight of transmission and torque converter (6) is approximately 544 kg (1200 lb). The weight of transmission and torque converter (6) with a retarder is approximately 590 kg (1300 lb).
Note: Three 1/2-20 bolts and one 3/8-24 bolt are used to mount the transmission to Tooling (D) .
Show/hide table
Illustration 4 | g02454024 |
Show/hide table
Illustration 5 | g02453439 |
Show/hide table
Illustration 6 | g02454022 |
- Remove bolts (7), cover (8), and O-ring seal (9) .
Show/hide table
Illustration 7 | g02454058 |
- Remove magnetic filter (10) and screen (11) .
Show/hide table
Illustration 8 | g02454076 |
- Remove bolts (12) and oil pan (13) .
Show/hide table
Illustration 9 | g02454077 |
- Remove seal (14) .
Show/hide table
Illustration 10 | g02454081 |
- Remove tube assembly (15) and tube assembly (16). Remove bolts (17) and housing (18) .
Show/hide table
Illustration 11 | g02454082 |
- Remove O-ring seal (19) .
Show/hide table
Illustration 12 | g02394401 |
- Remove bolts (20) in order to remove gear pump (21) .
Show/hide table
Illustration 13 | g02394382 |
Caterpillar Information System:
CX31 On-Highway Transmission Speed Sensor (Transmission) - Install
CX31 On-Highway Transmission Speed Sensor (Transmission) - Remove
3512C Oil Well Service Engines Fuel Filter Differential Pressure - Check
C15 Generator Sets Turbocharger - Inspect
CG137-08 and CG137-12 Industrial Engines Ignition Primary - Test
349F and 352F Excavators Machine System Specifications Cooling Lines
3512C Oil Well Service Engines Reference Information
3512C Oil Well Service Engines Coolant (ELC) - Change
3512C Oil Well Service Engines Coolant (DEAC) - Change
Carrier Roller Disassembly and Assembly Procedures {4154} Carrier Roller Disassembly and Assembly Procedures {4154}
CX31 On-Highway Transmission Oil Filter and Base (Power Train) - Remove and Install
Reconditioning Dimensions for Track Rollers {4154, 4180} Reconditioning Dimensions for Track Rollers {4154, 4180}
CX31 On-Highway Transmission Gear Pump (Torque Converter and Transmission) - Install
CX31 On-Highway Transmission Gear Pump (Torque Converter and Transmission) - Remove - Retarder
CX31 On-Highway Transmission Gear Pump (Torque Converter and Transmission) - Install - Retarder
3600 Distillate Fuel Engines Coolant (DEAC) - Change
3600 Distillate Fuel Engines Coolant (ELC) - Change
3600 Distillate Fuel Engines Coolant Extender (ELC) - Add
3600 Distillate Fuel Engines Coolant Level - Check
3600 Distillate Fuel Engines Coolant Sample (Level 1) - Obtain
3600 Distillate Fuel Engines Coolant Sample (Level 2) - Obtain
3600 Distillate Fuel Engines Coolant Temperature Regulator - Replace
3600 Distillate Fuel Engines Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
3600 Distillate Fuel Engines Engine Air Precleaner - Check/Clean