Fuel System Primary Filter (Water Separator) Element - Replace - if Equipped
Show/hide table
渗漏或溅溢到热表面或电气部件上的燃油会引起失火。 为防止可能的伤害,当更换燃油滤清器或油水分离器滤芯时,要将起动开关断开。 应立即将溅溢的燃油清除干净。 |
Show/hide table
注意 |
---|
不要让脏物进入燃油系统。 彻底清洁将要拆开的燃油系统部件的周围区域。 在拆开的燃油系统部件上安放适当的盖。 |
进行本保养之前应先将供油阀转至 OFF(关闭)位置。 在燃油滤清器下面放置一个托盘,以便盛接所有可能溢出的燃油。 立即清理溢出的燃油。
Show/hide table
图 1 | g00741109 |
典型示例 (1) 盖 (2) 锁环 (3) 滤芯 (4) 油水分离器储水杯 (5) 放油阀 |
- 关闭供油阀。
- 清洁燃油滤清器组件的外部。 使用滤芯 (3) 底部的放油阀将燃油排放到适当的容器中。 将油水分离器储水杯 ( 4)中的水排放到适当的容器中。 不是所有的发动机都配备了油水分离器。
注: 拆卸滤芯 (3)之前应将其内油位降低。 如果该滤芯底部没有配备放油阀,则应先拆下盖 ( 1)。 再拆下尼龙嵌套,以便降低滤芯内燃油的油位。 降低滤芯内燃油油位将会有助于防止拆卸滤芯时弄洒燃油。
Show/hide table注意 不要使用工具来拆下燃油滤清器。 试图使用滤清器扳手或滤清器拆卸带来拆下燃油滤清器会损坏锁环。
- 握住滤芯 (3),逆时针转到锁环 ( 2)。 拆下锁环 (2)。 应将旧滤芯拆下并废弃。
注: 如果该滤芯配备了沉淀杯,将沉淀杯从滤芯上拆下来。 彻底清洁沉淀杯。 检查 O 形密封圈是否磨损或损坏。 如有必要,更换新的 O 形密封圈。 将沉淀杯安装到新滤芯上。 用手拧紧沉淀杯。 用手拧紧是唯一应该使用的方法。
Show/hide table注意 安装燃油滤清器之前不要在其中注入燃油。 污染的燃油会加速燃油系统部件的磨损。
- 确保滤清器底座清洁。 将新滤芯完全推入滤清器底座内。
- 握住滤芯。 将锁环 ( 2) 安装到位。 顺时针旋转锁环以便将滤芯固定到滤清器底座上。
注: 如果此前已拆下尼龙嵌套,应将尼龙嵌套和盖 ( 1) 装回去。
- 向燃油系统注油。 有关更多信息,请参阅 操作和保养手册 , "燃油系统 - 泵注"。
Caterpillar Information System:
C4.4 (Mech) Marine Generator Set MCS-3 Engine Speed/Timing Sensor - Clean/Inspect
C4.4 (Mech) Marine Generator Set MCS-3 Fuel System - Prime - Duplex Fuel Filter if Equipped
C4.4 (Mech) Marine Generator Set MCS-3 Engine Oil and Filter - Change - Duplex Oil Filters
C4.4 (Mech) Marine Generator Set MCS-3 Engine Oil and Filter - Change - Single Oil Filter
C4.4 Industrial Engine Fuel System - Prime
C4.4 (Mech) Marine Generator Set MCS-3 Generator Lead Connections
2010/04/30 A Rework Procedure Improves the Seal Assembly Performance in Hydraulic Cylinders on Cat Products {7562}
C15 and C18 Petroleum Generator Sets Customer Assistance
C13, C15, and C18 Tier 4 Final Engines Exhaust Diffuser Adapter
C9.3 Tier 4 Final Engines Diesel Particulate Filter Has Changed Regeneration Interval
Introduction {0374, 4150, 7000, 7590, 7950} Introduction {0374, 4150, 7000, 7590, 7950}
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Electronic Modular Control Panel 4 (EMCP 4) - EMCP 4.3/4.4
C4.4 (Mech) Marine Generator Set MCS-3 Fuel System Secondary Filter - Replace
C13 Industrial Engines Electric Starting Motor
C9.3 Engines for Caterpillar Built Machines Pressure Sensor (DPF) - Remove and Install
C27 Generator Set Engines Air Inlet and Exhaust System - Inspect
C13, C15, and C18 Tier 4 Final Engines Electric Starting Motor
C27 and C32 Tier 4 Engines Component Location
317-7492 Wireless Radio{7338} 317-7492 Wireless Radio{7338}
348-5430 Multi-Tool Gp 2 {0709, 0769, 0785} 348-5430 Multi-Tool Gp 2 {0709, 0769, 0785}
C9.3 Engines for Caterpillar Built Machines Pressure Sensor (ARD Combustion Air) - Remove and Install
C7.1 Industrial Engine Fuel System Primary Filter/Water Separator - Drain
C4.4 Industrial Engine Accessory Drive
C4.4 Industrial Engine Accessory Drive - SAE "B"