Swing Drive - Disassemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 138-7573 | 连杆支架 | 2 |
B | 5P-5197 | 挡圈钳组件 | 1 |
开始:
- 拆下回转驱动。
- 将回转驱动定位到适当的支座上。 回转驱动的重量约为
281 kg (620 lb) 。 - 在回转驱动的盖和壳体上做出对准标记以便于组装。
Show/hide table
图 1 g02115775 - 将工具 (A) 和适当的起吊设备连接在盖 (2) 上。 盖 (2) 的重量约为
23 kg (51 lb) 。 拆下螺栓 (1) 和盖 (2)。Show/hide table图 2 g02115813 - 拆下太阳齿轮 (3) 和隔套 (4)。
- 需要用两个人来拆卸齿轮架组件 (5)。 齿轮架组件 (5) 的重量约为
23 kg (50 lb) 。Show/hide table图 3 g02115814 - 使用适当的锤子和冲头将弹簧销 (10) 打入行星齿轮轴 (6)。
- 从托架组件上拆下行星齿轮轴 (6)、止推垫圈 (7)、止推垫圈 (11)、行星齿轮 (9) 和轴承组件 (8)。
- 使用适当的锤子和冲头将弹簧销 (10) 从行星齿轮轴 (6) 上拆下。
- 重复步骤 6 至 8,以便从托架组件上拆下其他三个行星齿轮。
Show/hide table
图 4 g02115853 - 从托架上拆下挡圈 (12) 和太阳齿轮 (14)。
- 从太阳齿轮 (14) 上拆下挡圈 (13)。
Show/hide table
图 5 g02115915 Show/hide table图 6 g02115916 - 拆下隔套 (16)。
- 拆下用于将托架组件 (17) 固定到位的挡圈 (15)。
- 在托架组件 (17) 中的行星齿轮之间使用适当的钢制杆件。 确保钢制杆件处于托架组件 (17) 的中央。 将适当的起吊设备连接到钢制杆件上。 缓慢地从回转驱动壳体上提升托架组件 (17)。 齿轮架组件 (17) 的重量约为
39 kg (86 lb) 。Show/hide table图 7 g02115917 - 使用适当的锤子和冲头将弹簧销 (22) 打入行星齿轮轴 (19)。
- 从托架组件上拆下行星齿轮轴 (19)、止推垫圈 (18)、止推垫圈 (23)、行星齿轮 (21) 和轴承组件 (20)。
- 使用适当的锤子和冲头将弹簧销 (22) 从行星齿轮轴 (19) 上拆下。
- 重复步骤 15 至 17,以便从托架组件上拆下其他三个行星齿轮。
Show/hide table
图 8 g02115919 - 将工具 (A) 和适当的起吊设备连接到齿圈 (24)。 齿圈 (24) 的重量约为
39 kg (86 lb) 。 拆下齿圈 (24)。Show/hide table图 9 g02116593 - 使用工具 (B) 拆下挡圈 (25)。
Show/hide table
图 10 g03409949 Show/hide table图 11 g03409942 - 将工具 (A) 和适当的起吊设备连接到回转驱动壳体 (26)。 将回转驱动壳体 (26) 定位到适当的压具内。 回转驱动壳体 (26)、小齿轮轴和轴承保持架的组合重量约为
136 kg (300 lb) 。 - 在小齿轮轴的正下方放置合适的支座,以防止小齿轮轴在压出时掉落。
- 将小齿轮轴 (28)和隔套 (27) 从回转驱动壳体 (26) 上拆下。
Show/hide table
图 12 g03410004 - 在保持架 (30) 和回转驱动壳体 (26) 上做对准标记,以便于组装。
- 拆下用于将保持架 (30) 固定到回转驱动壳体上的螺栓 (29)。 拆下保持架 (30)、O 形密封圈 (31) 和轴承 (33)。
- 将唇形密封 (28) 从保持架 (30) 上拆下。
Show/hide table
图 13 g03410014 - 从回转驱动壳体 (26) 上拆下轴承 (34)。
Caterpillar Information System:
C15 and C18 Industrial Engines Water Temperature Regulator Housing - Remove and Install - For Series Turbocharger Applications
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Generator Bearing Temperature - Test/Record
C11 and C13 Engines Water Pump
Inspection and Reuse of Critical Fasteners Used in All Engines {7553, 7553} Inspection and Reuse of Critical Fasteners Used in All Engines {7553, 7553}
C27 and C32 Engines for Caterpillar Built Machines Cylinder Head Valves
C15 and C18 Industrial Engines Precooler - Remove and Install - For Series Turbo Applications
C-10, C-12 and C-15 On-Highway Engines Configuration Parameters - Customer Specified Parameters
C13 Industrial Engines Temperature Sensor (NOx Reduction System) - Cooled Diesel Exhaust Gases
C9.3 Tier 4 Final Engines Temperature Sensor (NOx Reduction System)
Installation and Initial Start-Up Procedure for G3508B A3 Engines{1000} Installation and Initial Start-Up Procedure for G3508B A3 Engines{1000}
C13, C15, and C18 Tier 4 Final Engines Inlet Manifold Temperature Sensor - Charge Air Cooler Outlet
C13 Industrial Engines Fuel Pressure Sensor
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Swing Drive - Assemble
C27 and C32 Tier 4 Engines Pressure Sensor (NRS Differential)
2010/03/09 A New Screw Is Available for the Rocker Arm Assemblies of Some Truck Engines {1123}
2010/03/12 A New Screw Is Available for the Rocker Arm Assemblies of Some Commercial Engines {1123}
2010/03/10 A New Screw Is Available for the Rocker Arm Assemblies of Some Machine Engines {1123}
C13 Industrial Engines Pressure Sensor (NRS Absolute)
2010/10/08 A Slave Relay Should be Used for Customer Connections to EMCP 3 On Certain Generator Sets {4490}
Torque Converter, Divider, Drive Line, and Drive Axle Reuse and Salvage Manual Contents {0374, 3000, 3050, 3100, 3250, 3251, 3253, 3258} Torque Converter, Divider, Drive Line, and Drive Axle Reuse and Salvage Manual Contents {0374, 3000, 3050, 3100, 3250, 3251, 3253, 3258}
2010/03/22 A Procedure to Properly Torque the Fittings on the Fuel Manifold Group on Certain C13 and C15 On-Highway Truck Engines Is Available {1274, 1380, 1702}
C9.3 Tier 4 Final Engines Fuel Filter Base
797F Off-Highway Truck Power Train Gear Pump (Rear Axle Lubrication) - Remove and Install
EMCP4.3/4.4 Data Link