Customer Specified Parameters Worksheet
Show/hide table
Customer Specified Parameters Worksheet | |
---|---|
ECM Identification Parameter | |
Equipment ID | |
Engine Rating Parameter | |
Rating Number | |
Speed Control | |
Low Idle Speed | |
Engine Configuration Parameter | |
Ether Solenoid Configuration | |
Engine Idle Shutdown | |
Minimum Ambient Air Temperature | |
Maximum Ambient Air Temperature | |
Shutdown Enable Status | |
Shutdown Delay Time | |
Ambient Temperature Override Enable Status | |
Air Shutoff | |
Air Shutoff | |
Aftertreatment Configuration | |
ARD Auto Regeneration Enable Status | |
DPF #1 Soot Loading Sensing System Configuration Code | |
High Soot Load Aftertreatment Protection | |
Multiple Engines on J1939 | |
Engine Location | |
PTO and Throttle Lock Parameters | |
Throttle Lock Feature Installation Status | |
PTO Mode | |
Throttle Lock Engine Set Speed 1 | |
Throttle Lock Engine Set Speed 2 | |
Throttle Lock Increment Speed Ramp Rate | |
Throttle Lock Decrement Speed Ramp Rate | |
Throttle Lock Engine Set Speed Increment | |
Throttle Lock Engine Set Speed Decrement | |
Miscellaneous | |
Monitoring Mode Shutdowns | |
Monitoring Mode Derates | |
Limp Home Desired Engine Speed | |
Engine Acceleration Rate | |
Engine Speed Deceleration Ramp Rate | |
Intermediate Engine Speed | |
Engine Fan Control | |
Engine Fan Control | |
Engine Fan Type Configuration | |
Pulley Ratio | |
Temperature Error Increasing Hysteresis | |
Temperature Error Decreasing Hysteresis | |
Current Ramp Rate | |
Fan Speed | |
Top Fan Speed | |
Minimum Desired Fan Speed | |
Solenoid Minimum Current | |
Solenoid Maximum Current | |
Solenoid Dither Frequency | |
Solenoid Dither Amplitude | |
Cooling Fan Temperatures | |
Charge Air Cooler Outlet Temperature Input Enable | |
Maximum Air Flow Charge Air Cooler Outlet Temperature | |
Minimum Air Flow Charge Air Cooler Outlet Temperature | |
Coolant Temperature Input Enable Status | |
Maximum Air Flow Coolant Temperature | |
Minimum Air Flow Coolant Temperature | |
Transmission Oil Temperature Input Enable Status | |
Maximum Air Flow Transmission Oil Temperature | |
Minimum Air Flow Transmission Oil Temperature | |
Hydraulic Oil Temperature Input Enable Status | |
Maximum Air Flow Hydraulic Oil Temperature | |
Minimum Air Flow Hydraulic Oil Temperature | |
Auxiliary #1 Temperature Input Enable Status | |
Maximum Air Flow Auxiliary #1 Temperature | |
Minimum Air Flow Auxiliary #1 Temperature | |
Auxiliary #2 Temperature Input Enable Status | |
Maximum Air Flow Auxiliary #2 Temperature | |
Minimum Air Flow Auxiliary #2 Temperature | |
Fan Reversing | |
Reversing Feature | |
Reverse Operation Early Termination Enable Status | |
Manual Purge | |
Suspend Purge | |
Purge Cycle Interval | |
Purge Cycle Duration | |
Configurable Inputs | |
Coolant Level Switch | |
Air Filter Restriction Switch Installation Status | |
Air Filter Restriction Switch Configuration | |
Water in Fuel Switch Installation Status | |
User Defined Switch Installation Status | |
Auxiliary Temperature Sensor Installation Status | |
Auxiliary Pressure Sensor Installation Status | |
Fuel Filter Differential Pressure Switch Configuration | |
Diesel Particulate Filter Regeneration Force/Inhibit Switch Installation | |
Diesel Particulate Filter Regeneration Inhibit Indicator Installation | |
Diesel Particulate Filter Soot Loading Indicator Installation | |
Regeneration Active Indicator Installation | |
J1939 Continuous Fault Handling | |
Remote Torque Speed Control Enable Status | |
System Settings | |
System Operating Voltage Configuration | |
Passwords | |
Customer Password 1 | |
Customer Password 2 | |
Security Access Parameters | |
CAN Communication Protocol Write Security | |
CAN Communication Protocol Read Security |
Caterpillar Information System:
C7.1 Industrial Engine and Generator Set Customer Specified Parameters Table
3508C, 3512C and 3516C Locomotive Engines Water Lines
C7.1 Industrial Engine and Generator Set Mode Selection Circuit - Test
3508C, 3512C and 3516C Locomotive Engines Water Lines
793F Off-Highway Truck Engine Supplement Turbocharger - Remove and Install
793F Off-Highway Truck Engine Supplement Damper - Remove and Install
797F and 797F XQ Off-Highway Truck Steering System Oil Filter (Hydraulic Fan, Steering Pump Case Drain)
2009/10/01 Improved Exhaust Components and Heat Shields Are Used on Some G3520C Engines {1059, 1067}
C4.4 Industrial Engine Cooling System Supplemental Coolant Additive (SCA) - Test/Add
C4.4 Industrial Engine Cooling System Coolant Extender (ELC) - Add
3508C, 3512C and 3516C Locomotive Engines Water Lines
3508C, 3512C and 3516C Locomotive Engines Air Inlet and Exhaust Lines
797F and 797F XQ Off-Highway Truck Braking System Oil Filter (Brake Cooling, Hoist)
2009/08/31 Diagnostic Process for Fuel Rail Pressure Sensor {127A, 1439}
2009/08/17 New Metal Shipping Stands for 3500 Machine Engines {1000}
2009/08/01 Diagnostic Publications for the Systems of the Hydraulic Electronic Unit Injector (HEUI) have been Updated {1100, 1126, 1250, 1251, 1261, 1290}
2009/08/10 Diagnostic Publications for the Systems of the Hydraulic Electronic Unit Injector (HEUI) have been Updated {1100, 1126, 1250, 1251, 1261, 1290}
793F and 797F Off-Highway Trucks Chassis Electronic Control System Glossary of Electrical Terms
C13 Industrial Engines Turbocharger
C18 Industrial Engine Aftercooler - Test
2009/08/03 A New Bolt Is Used on the Valve Mechanism Gp of All 3500 Machine Engines {1102, 1107, 1120, 1121, 1123, 1209}
2009/08/03 The Connector for the Chassis Harness and the Platform Harness Should Be Tightened to the Specified Torque on Certain Excavators {1408}
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Battery Disconnect Switch - If Equipped
3516B Engine for 994F and 994H Wheel Loaders Electronic Service Tool Does Not Communicate