Front Suspension (Cylinder) - Assemble
组装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7573     | 连杆支架     | 4     |
B     | 138-7576     | 连杆支架     | 2     |
C     | 129-1966     | 多功能润滑脂     | 1     |
D     | 6H-1717     | 螺栓     | 1     |
5P-8245 | 硬垫圈     | 1     | |
E     | 155-0695     | 螺纹锁固胶     | 1     |
F     | 194-7585     | 气动扳手总成     | 1     |
G     | 8T-9580     | 液压油     | 4     |
1U-9891 | 液压油添加剂     | 1     |
- 将工具 (C) 涂敷到环 (28) 上。 安装环 (28) 。
Show/hide table
图 1 | g01929157 |
- 将工具 (C) 涂敷到唇形密封 (29) 上。 安装唇形密封 (29) 。 将工具 (C) 涂敷到唇形密封 (30) 上。 安装唇形密封 (30) 。
安装护圈 (27) 、螺栓 (26) 和垫圈。
- 将工具 (G) 涂敷到环 (18) 、O 形密封圈 (19) 、环 (20) 和 (21) 、O 形密封圈 (22) 以及环 (23) 上。
Show/hide table
图 2 | g01285540 |
- 安装环 (18) 、O 形密封圈 (19) 、环 (20) 和 (21) 、O 形密封圈 (22) 以及环 (23) 。
- 将工具 (G) 涂敷到密封件 (25) 上。 安装密封件 (25) 。
Show/hide table
图 3 | g01285523 |
- 使用工具 (A) 以便安装压盖 (17) 。
Show/hide table
图 4 | g01933226 |
- 安装环 (24) 。 将工具 (G) 涂敷到环 (24) 上。
- 将工具 (C) 涂敷到 O 形密封圈 (16) 上。 安装 O 形密封圈 (16) 。
Show/hide table
图 5 | g01285428 |
- 使用适当的锤子安装端块 (14) 。
Show/hide table
图 6 | g01933234 |
- 安装护圈 (15) 。
Show/hide table
图 7 | g01285582 |
- 安装板 (13) 。 将工具 (E) 涂敷到螺栓 (12) 上。 安装螺栓 (12) 。
注: 拧紧螺栓 (12) 时,端块 (14) 不得转动。
Show/hide table
图 8 | g01285587 |
- 安装珠体 (11) 。
Show/hide table
图 9 | g01285590 |
- 使用适当的起吊设备安装活塞 (9) 。 活塞 (9) 的重量大约为 73 kg (160 lb)。
Show/hide table
图 10 | g01285594 |
- 安装螺栓 (10) 。 连接工具 (B) 。 安装环 (8) 。
Show/hide table
图 11 | g01928464 |
- 将活塞杆 (7) 部分安装到壳体 (6) 中。 将工具 (G) 涂敷到环 (8) 上。 将活塞杆 (7) 安装到壳体 (6) 中。
Show/hide table
图 12 | g01285656 |
- 安装其余的螺栓 (10) 。 使用工具 (F) 以便拧紧螺栓 (10) 。
Show/hide table
图 13 | g01285664 |
- 用 73.4 L (19.4 US gal) 的工具 (L) 加注壳体 (6) 。
Show/hide table
图 14 | g01285677 |
- 将工具 (G) 涂敷到环 (4) 和 O 形密封圈 (5) 上。 安装 O 形密封圈 (5) 和环 (4) 。
Show/hide table
图 15 | g01933413 |
- 使用工具 (A) 和适当的起吊设备安装缸盖 (2) 。 缸盖 (2) 的重量约为 140 kg (310 lb)。
Show/hide table
图 16 | g01928433 |
Show/hide table
图 17 | g01928315 |
- 安装螺栓 (3) 。
- 从适当的夹具上拆下前悬架油缸 (1) 。 前悬架油缸 (1) 的重量约为 3450 kg (7600 lb)。
Show/hide table
图 18 | g01928258 |
Show/hide table
为了避免可能造成的人身伤害,使用适当的支撑装置来支撑悬架油缸的重量。 不要在没有使用适当的支撑时,而尝试将悬架油缸以末端竖立。 未使用适当的支撑装置可能导致工作区域中的人员受伤甚至死亡。 |
End By: 安装前悬架。
Caterpillar Information System:
797 Off-Highway Truck Front Suspension (Cylinder) - Disassemble
C9 Marine Engines Configuration Parameters
C9 Marine Engines Diagnostic Flash Code Retrieval
3000 Frame SR5 Electric Power Generation Diode Assembly - Remove and Install
3000 Frame SR5 Electric Power Generation Coupling - Install
C9.3 Industrial Engine Turbocharger
3000 Frame SR5 Electric Power Generation Coupling - Remove
C32 Petroleum Engines General Hazard Information
3512B and 3516B Engines Exhaust Manifold
C9.3 Tier 4 Final Engines Water Lines
C9.3 Engines for Caterpillar Built Machines Relief Valve (Fuel) - Remove and Install
C7.1 Industrial Engine Diesel Particulate Filter - Clean
The Loss of Fuel Prime in Some C32 Engines{1250, 1280} The Loss of Fuel Prime in Some C32 Engines{1250, 1280}
797F and 797F XQ Off-Highway Trucks Machine Systems Hoist Cylinder - Remove and Install
C9.3 Industrial Engine Turbocharger
2009/07/13 Improved Diagnostic Procedures Are Now Used to Determine Proper Belt Alignment on C9 Marine Engines {1358, 1397}
3500 Engines Exhaust Manifold
3500B Engines Air Shutoff
C9.3 Engines for Caterpillar Built Machines Fuel Manifold - Remove and Install - Return
C13 Engine for Combat and Tactical Vehicles Belt Tensioner
UPS Bearing Type I to G3.5 Conversion{4480} UPS Bearing Type I to G3.5 Conversion{4480}
Instructions For Converting Uninterruptible Power Supplys With Hall Effect Probes To The G3.5 Load Cell{4480} Instructions For Converting Uninterruptible Power Supplys With Hall Effect Probes To The G3.5 Load Cell{4480}
2009/05/25 Correction to Schematics for the Control Group {1408}
G3304B and G3306B Engines Aftercooler - Remove