Spark Plug Adapter - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-5559     | 火花塞适配器扳手     | 1     |
B     | 5P-3931     | 防粘结剂     | -     |
开始:
- 拆下火花塞。
Show/hide table
热的冷却液、蒸汽和碱会造成人身伤害。 在工作温度下,发动机冷却液是热的而且处在压力下。 散热器和所有到加热器的管路或发动机中都有热的冷却液或蒸汽。 与它们的任何接触都会造成严重烫伤。 只有当发动机停机且冷却系统压力盖已经冷却到可以徒手触摸时,再慢慢拆下冷却系统压力盖以释放压力。 不要试图在冷却液还热的时候去拧紧软管接头,软管会脱落而造成灼伤。 警告:冷却系统的冷却液添加剂含碱。 应避免它与皮肤和眼睛接触。 |
- 将冷却系统中的冷却液抽到缸盖以下液位。 请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
- 使用工具 (A) 拆下火花塞适配器 (1) 和密封垫。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 1 | g00991174 |
安装步骤
- 将肥皂液涂抹在 O 形密封圈 (3) 。 将一个新的 O 形密封圈 (3) 和密封垫 (2) 安装在火花塞适配器 (1) 上。
Show/hide table
图 2 | g00991182 |
- 将工具 (B) 涂抹在火花塞适配器的螺纹上。
- 安装火花塞适配器。 使用工具 (A) 拧紧火花塞适配器至扭矩为 95 ± 7 N·m (70 ± 5 lb ft)。
- 向冷却系统加注冷却液到正确的液位。 请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
End By: 安装火花塞。
Caterpillar Information System:
G3304B and G3306B Engines Spark Plugs - Remove and Install
C7 Petroleum Engine Plate Locations and Film Locations
G3304B and G3306B Engines Carburetor - Install
C32 Petroleum Engines Installation Environment
C7 Petroleum Engine Installation Environment
C13 Engine for Caterpillar Built Machines Belt Tensioner - Remove and Install
G3304B and G3306B Engines Indicator Lamp - Test
C7.1 Industrial Engine and Generator Set 5 Volt Sensor Supply Circuit - Test
C18 Marine Generator Set Model View Illustrations
3516B Engine for 994F and 994H Wheel Loaders Power Is Intermittently Low or Power Cutout Is Intermittent
2009/06/01 A Hotline for the Fuel Systems for Hydraulic Electronic Unit Injectors (HEUI) Is Now Available. {1251, 1290}
2009/06/08 A Hotline for the Fuel Systems for Hydraulic Electronic Unit Injectors (HEUI) Is Now Available. {1251, 1290}
C13 Engine for Caterpillar Built Machines Accessory Drive - Remove and Install - Brackets and Pulleys
C9 Engine Monitoring System
C32 Petroleum Engines Monitoring System
G3304B and G3306B Engines Exhaust Manifold - Remove
C7 Engines for Combat and Tactical Vehicles Safety Messages
2009/06/22 Fuel Injection Pump Latch Valve {1251}
3500B Engines for Caterpillar Built Power Modules Fuel Injector Mechanism
C9.3 Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
2009/06/08 The Packaging Consist of the C9 Genset Has Been Changed {1000, 1021, 7002}
C7 Industrial Engines Turbocharger
C13 Engine for Combat and Tactical Vehicles Turbocharger
G3304B and G3306B Engines Exhaust Manifold - Install