Turbocharger - Install - Dual Turbocharger
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 5P-3931     | Anti-Seize Compound     | -     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
- Attach a suitable lifting device to turbocharger (7). The weight of turbocharger (7) is approximately 23 kg (51 lb). Install turbocharger (7) on the exhaust manifold.
Show/hide table
Illustration 1 | g01680576 |
- Apply Tooling (A) to the threads of bolts (9). Tighten bolts (9) to a torque of 55 ± 5 N·m (41 ± 4 lb ft).
- Connect tube assembly (8) .
- Connect tube assemblies (6) .
Show/hide table
Illustration 2 | g01680556 |
- Install clamp assembly (5). Tighten the nut on clamp assembly (5) to a torque of 14 ± 1 N·m (124 ± 9 lb in). Lightly tap around the diameter of the clamp assembly with a soft hammer. Tighten the nut to a torque of 14 ± 1 N·m (124 ± 9 lb in).
- Position guard (3) and install bolts (2) .
Show/hide table
Illustration 3 | g01789073 |
Show/hide table
Illustration 4 | g01789074 |
- Install bolts (1) and install bolts (4) .
- Fill the Cooling System with Coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
End By: Install the air cleaner. Refer to Disassembly and Assembly, "Air Cleaner - Remove and Install".
Caterpillar Information System:
C18 Fire Pump Industrial Engine Turbocharger - Remove - Dual Turbocharger
C18 Fire Pump Industrial Engine Fuel Filter Base - Install
C18 Fire Pump Industrial Engine Fuel Filter Base - Remove
C18 Fire Pump Industrial Engine Fuel Priming Pump - Remove and Install
G3516 Petroleum Engines Gas Pressure Regulator - Install
3500B Engines Air Inlet and Exhaust Lines
3500B and 3500C Marine Engines Camshaft
3408E and 3412E Engines for Caterpillar Built Machines Water Temperature Regulator
G3516 Petroleum Engines Gas Pressure Regulator - Remove
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Air Starting Motor - Install
C15 Petroleum Engines Acceleration Is Poor or Throttle Response Is Poor
G3508J, G3516J, and G3520J Engines Air Starting Motor - Remove
3500B Generator Set Engines Turbocharger
3500B Engines for Caterpillar Built Power Modules Turbocharger
320D and 323D Excavators Machine System Specifications Grease Lines
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Exhaust Elbow - Remove and Install
Upgrade to Air/Fuel Ratio Control, Nitrogen Oxide Sensor, and a Single Turbocharger for Enhanced Performance of G3508 Engines{1000, 1052, 1270, 191N} Upgrade to Air/Fuel Ratio Control, Nitrogen Oxide Sensor, and a Single Turbocharger for Enhanced Performance of G3508 Engines{1000, 1052, 1270, 191N}
R250 Automatic Voltage Regulator High Voltage
Parts for Updating Early 3406E Aftercooler Cores{1063} Parts for Updating Early 3406E Aftercooler Cores{1063}
R250 Automatic Voltage Regulator General Information
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Aftercooler - Remove and Install
C18 Fire Pump Industrial Engine Water Pump - Remove
Prevention of Leaks in the C18 Marine Heat Exchanger Frame {1379, 1395} Prevention of Leaks in the C18 Marine Heat Exchanger Frame {1379, 1395}
No Starboard Throttle Signal{3065, 4490} No Starboard Throttle Signal{3065, 4490}