Position Sensor (Lift Linkage) - Replace
Show/hide table
Illustration 1 | g06134063 |
Right side of front frame (1) Lift linkage position sensor |
Show/hide table
NOTICE |
---|
The position sensor can be damaged if too much force is applied against the internal stops of the sensor. Be careful when removing the position sensor lever or rotating the shaft attached to the sensor. |
Reference: For the correct procedure to calibrate the Lift Linkage Position Sensor, refer to the Service Manual module Testing and Adjusting, M0083603, "992K Wheel Loader", "Linkage Sensor Calibrations (Lift & Tilt)" for the machine that is being serviced.
Caterpillar Information System:
992K Wheel Loader Piston Pump (Implement) Main Relief Valve Pressure - Test and Adjust
992K Wheel Loader Calibration Error Codes
Announcing a Serviceability Update for Track Roller Frames for Certain D8N and D8R Track-Type Tractors {4151} Announcing a Serviceability Update for Track Roller Frames for Certain D8N and D8R Track-Type Tractors {4151}
New Clamshell Hood Bracket Is Now Used on Certain 980K, 980M, and 982M Wheel Loaders {7251} New Clamshell Hood Bracket Is Now Used on Certain 980K, 980M, and 982M Wheel Loaders {7251}
992K Wheel Loader Calibrations (Cat ET)
994K Wheel Loader Machine Systems Lift Cylinder - Remove and Install
M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B} M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}
525D, 535D, 545D and 555D Wheel Skidders Solenoid Valve - Test
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 Editing Truck and Material Lists
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Lubrication System
Installation Instructions For The New Solid-State Main Power Relay On Certain D6T Track-Type Tractors {1422, 1426} Installation Instructions For The New Solid-State Main Power Relay On Certain D6T Track-Type Tractors {1422, 1426}
A New Solid-State Main Power Relay Is Now Used on Certain D6T Track-Type Tractors {1422, 1426} A New Solid-State Main Power Relay Is Now Used on Certain D6T Track-Type Tractors {1422, 1426}
C175–16 Locomotive Engine Air in Fuel - Test
992K Wheel Loader Position Sensor (Tilt Linkage) - Replace
953K and 963K Track-Type Loaders Caterpillar Approved Work Tools
MD6310 Rotary Drill Belt - Inspect/Adjust/Replace
MD6200 Rotary Drill Cab Air Filter (Fresh Air) - Clean/Replace
992K Wheel Loader Pilot Control Actuator Pressure - Check
D6T Track-Type Tractor Electrohydraulic System Diagnostic Capabilities
312D2 and 313D2 Excavators Plate Locations and Film Locations
Improved Viscous Cab Mount Is Now Used on Certain 980M and 982M Medium Wheel Loaders {7301, 7301} Improved Viscous Cab Mount Is Now Used on Certain 980M and 982M Medium Wheel Loaders {7301, 7301}
An Improved Latch Assembly in the Rear Guard Is Now Used on Certain D5R and D6N Track-Type Tractors {7187} An Improved Latch Assembly in the Rear Guard Is Now Used on Certain D5R and D6N Track-Type Tractors {7187}
New Secondary Steering Software Control Is Now Used on 980H Wheel Loaders {4300, 4324, 4800, 4808, 7610, 7620} New Secondary Steering Software Control Is Now Used on 980H Wheel Loaders {4300, 4324, 4800, 4808, 7610, 7620}
Installing The 523-4907 Work Tool Positioner Kit {5112, 5264, 5479} Installing The 523-4907 Work Tool Positioner Kit {5112, 5264, 5479}