The user is responsible for the performance of maintenance. All adjustments, the use of proper lubricants, fluids, filters, and the replacement of components due to normal wear and aging are included. Failure to adhere to proper maintenance intervals and procedures may result in diminished performance of the product and/or accelerated wear of components.
Use mileage, fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST, to determine the maintenance intervals. Products that operate in severe operating conditions may require more frequent maintenance. Refer to the maintenance procedure for any other exceptions that may change the maintenance intervals.
Note: Before each consecutive interval is performed, all maintenance from the previous interval must be performed.
Use the service hour meter for the machine or machine system to determine when maintenance should be performed.
When Required
Battery - RecycleCircuit Breakers - Reset
Cutting Edges and End Bits - Inspect/Replace
Display and Camera - Clean
Draft Arm Wear Plates - Check/Adjust
Ejector Carrier Rollers - Check/Adjust
Ejector Guide Rollers - Check/Adjust
Ejector Support Rollers - Check/Adjust
Engine - Clean
Engine Air Filter Primary Element - Replace
Engine Air Filter Secondary Element - Replace
Ether Starting Aid Cylinder - Replace
Film (Product Identification) - Clean
Fuses - Replace
Oil Filter - Inspect
Radiator Core - Clean
Secondary Steering - Test
Window Washer Reservoir - Fill
Window Wiper - Inspect/Replace
Windows - Clean
Every 10 Service Hours or Daily
Backup Alarm - TestBrakes, Indicators and Gauges - Test
Cooling System Coolant Level - Check
Differential and Final Drive Oil Level - Check
Engine Oil Level - Check
Fuel System Water Separator - Drain
Hydraulic Oil Cooler - Clean
Hydraulic System Oil Level - Check
Push Plate - Lubricate
Radiator Core - Clean
Seat Belt - Inspect
Transmission Oil Level - Check
Every 50 Service Hours or Weekly
Bail Bearings and Push Plate Spring - LubricateBowl Lift Cylinder Bearings - Lubricate
Cab Air Filter - Clean/Replace
Fuel Tank Water and Sediment - Drain
Hitch - Lubricate
Tire Inflation - Check
Every 250 Service Hours or Monthly
Braking System - TestEngine Oil Sample - Obtain
Hydraulic System Oil Sample - Obtain
Transmission Oil Sample - Obtain
Wheel Bearing Oil Level - Check
Every 500 Service Hours or 3 Months
Accumulator (Brake) - CheckAccumulator (Cushion Hitch) - Check
Battery - Clean/Check
Belts - Inspect/Replace
Brake Pads - Check
Cooling System Coolant Sample (Level 1) - Obtain
Differential and Final Drive Oil Sample - Obtain
Engine Oil and Filter - Change
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Fuel Tank Cap and Strainer - Clean
Hydraulic System Oil Filter - Replace
Oil Filter (Brake, Hydraulic Fan) - Replace
Oil Filter (Cushion-Hitch) - Replace
Transmission Oil Filter and Magnetic Screen - Replace/Clean
Every 1000 Service Hours or 6 Months
Breather (Differential and Final Drive) - ReplaceBreather (Fuel Tank) - Replace
Breather (Transmission) - Replace
Condenser (Refrigerant) - Clean
Hydraulic Tank Breaker Relief Valve - Replace
Rollover Protective Structure (ROPS) - Inspect
Service and Parking Brake - Inspect
Suction Screen (Transmission Scavenge) - Clean
Transmission Oil - Change
Every Year
Refrigerant Dryer - ReplaceEvery 2000 Service Hours or 1 Year
Battery or Battery Cable - Inspect/ReplaceCooling System Coolant Sample (Level 2) - Obtain
Differential Thrust Pin Clearance - Check
Differential and Final Drive Oil - Change
Ejector Carrier Rollers - Inspect/Pack/Replace
Ejector Guide Rollers - Inspect/Pack/Replace
Ejector Support Rollers - Inspect/Pack/Replace
Hitch - Inspect
Hydraulic System Oil - Change
Wheel Bearing Oil - Change
Every 2500 Service Hours
Electronic Unit Injector - Inspect/AdjustEngine Compression Brake Valve Lash - Check
Engine Valve Lash - Check