Equalizer Bar - Disassemble
Disassembly Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 136-1452 | Internal Tip Pliers | 1 |
| B | 6V-3160 | Hydraulic Cylinder Gp | 1 |
| 350-7768 | Electric Hydraulic Pump Gp(115V) | 1 | |
| 350-7769 | Electric Hydraulic Pump Gp (230V) | 1 | |
| 9U-5267 | Puller Stud | 1 | |
| 2J-3507 | Nut | 1 | |
| 3K-5234 | Hard Washer | 1 | |
| 6V-2098 | Press Sleeve | 1 | |
| FT2802 | Plate | 1 | |
| C | 350-7768 | Electric Hydraulic Pump Gp (115V) | 1 |
| 350-7769 | Electric Hydraulic Pump Gp (230V) | 1 | |
| 6V-3175 | Hydraulic Cylinder Gp | 1 | |
| 4C-9634 | Puller Stud | 1 | |
| 9U-6832 | Nut | 1 | |
| 4K-0684 | Hard Washer | 1 | |
| 6V-4035 | Sleeve | 1 | |
Start By:
- Remove the equalizer bar.
Show/hide table
 |
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death. |
 |
Show/hide table
| NOTICE |
|---|
Do not use threaded rods that have not been hardened as tooling with hydraulic cylinders. The maximum rated tonnage should be stamped on one end of the puller studs. Do not use threaded rods that have not been stamped with the rated tonnage. |
- Remove spacers (5) and seals (6) from equalizer bar (1) .
Show/hide table
 | |
| Illustration 1 | g01261037 |
- Remove plug (2), O-ring seal (3), and fitting (4) from each end of equalizer bar (1) .
- Remove seals (8) from each end of equalizer bar (1) .
- Use Tooling (A) to remove retaining rings (7) from each end of equalizer bar (1) .
- Use Tooling (B) to remove bearing (9) from each end of the equalizer bar.
Show/hide table
 | |
| Illustration 2 | g01261042 |
- Use Tooling (C) to remove center bearing (10) from the equalizer bar.
Show/hide table
 | |
| Illustration 3 | g01261043 |
Caterpillar Information System:
C280 Marine Engines Exhaust System Contains Coolant
D6R2 Track-Type Tractor Power Train Equalizer Bar - Remove and Install
335F Excavator Machine System Specifications Front Lines
D6N Track-Type Tractor Specifications
335F CR Excavator C7.1 Engine Supplement Engine - Remove and Install
335F Excavator Machine System Specifications Boom - 6.15 m (20.177 ft)
335F Excavator Machine System Specifications Handrail
335F Excavator Machine System Specifications Front Lines
C7.1 Engines Electrical Connectors
335F Excavator Machine System Specifications Boom Cylinder
C4.4 and C7.1 Engines Diagnostic Capabilities
335F Excavator Machine System Specifications Front Lines
D6R2 Track-Type Tractor Power Train Equalizer Bar - Assemble
C3.4B Industrial Engine Severe Service Application
PL72 Pipelayers Power Train Final Drive Planetary Carrier (In Chassis) - Remove and Install
D6N Track-Type Tractor Daily Inspection
D6R2 Track-Type Tractor Power Train Final Drive, Steering Planetary, and Brake (Right Side) - Remove and Install
D6R2 Track-Type Tractor Power Train Steering Differential and Brake - Disassemble
335F Excavator Swing Bearing - Lubricate
D6R2 Track-Type Tractor Power Train Steering Differential and Brake - Assemble
D6R2 Track-Type Tractor Power Train Final Drive - Remove and Install
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System Location of Components (Fan Hydraulic System)
D6R2 Track-Type Tractor Power Train Final Drive - Disassemble
C27 and C32 Engines for Caterpillar Built Machines Shutdown (Ground Level) - Test