Starting Motor - Assemble
Note: The following procedure is only for the 24 volt starting motor.
Show/hide table
Tools Needed | |
---|---|
1P-0510 Driver Gp | |
1P-1855 Retaining Ring Pliers |
- Lubricate the following items with SAE 20W oil: bushings, seals and oil wicks.
Show/hide table
Illustration 1 g00705427 - Put the field winding assembly (35) and pole shoes (34) in position in the starting motor housing. Install the twelve screws (37) and tighten to a torque of
20.3 ± 2.3 N·m (180 ± 20 lb in) . Install the motor terminal (36), the washers and the nut. Tighten the nut to a torque of30 ± 3 N·m (22 ± 2.0 lb ft) .Show/hide tableIllustration 2 g00705400 - Use a 1P-0510 Driver Gp to install the bushing (32) and the seal (33) into the shift lever housing .
Show/hide table
Illustration 3 g00705073 - Install the seals on the shaft (31). Position the shift lever assembly (28) into the shift lever housing. Use a 1P-1855 Retaining Ring Pliers to install the shaft (31) and the snap ring .
- Install the O-ring seal and the gasket onto the shift lever housing. Set the shift lever housing assembly (29) onto the starting motor housing in the correct position. Install the seven bolts and tighten the bolts (30) to a torque of
12.2 ± 2.7 N·m (108 ± 24 lb in) .Show/hide tableIllustration 4 g00704879 - Use 5P-0960 Molybdenum Grease to lubricate the armature assembly bushing areas. Do not grease the armature core or the commutator.
- Put the pinion drive assembly (27) into position in the fork of the shift lever. Put the spacer on the armature assembly (26). Install the armature assembly (26) into the starting motor housing and the shift lever housing. Slide the armature assembly (26) into the pinion drive assembly (27).
Show/hide table
Illustration 5 g00704875 - Use a 1P-0510 Driver Gp to install the bushing (25) into the pinion drive housing (23).
Show/hide table
Illustration 6 g00704870 - Slide the pinion drive housing assembly (23) onto the shift lever housing in the correct position. Install the six screws (24) and tighten to a torque of
20 ± 3 N·m (178 ± 27 lb in) .Show/hide tableIllustration 7 g00704856 - Position the insulator (22), the plate (21) and the brush holders onto the brush plate assembly. Install the screws (20) and tighten the screws .
Show/hide table
Illustration 8 g00704842 - Use a 1P-0510 Driver Gp in order to install the bushing (19) into the rear frame assembly (14) .
Show/hide table
Illustration 9 g00705811 - Install the O-ring seal (18) onto the rear frame assembly. Position the gasket onto the brush plate assembly (16). Put the washers and the insulator on the negative terminal.
- Position brush plate assembly (16) onto the rear frame and install the three screws. Install the negative terminal insulator, the washers and the nut. Tighten the nut to a torque of
30 ± 3 N·m (22 ± 2 lb ft) . - Install the brushes (15) with the brush springs against the side of each brush. Tighten the lead screw for the brushes to a torque of
2.9 ± 1.0 N·m (26 ± 8 lb in) .Show/hide tableIllustration 10 g00705821 - Put the washer onto the armature assembly. Position the rear frame assembly (14) over the commutator. Push the brushes (15) into the holders so that the springs are on top of the brushes.
- Put the rear frame assembly against the starting motor housing in the correct position. Install the six bolts and tighten the bolts to a torque of
12.2 ± 2.7 N·m (108 ± 24 lb in) . Connect the wire assembly to the negative terminal on the end frame assembly.Show/hide tableIllustration 11 g00705835 - Connect the three field winding leads (38) to the brush plate assembly. Tighten the screws to a torque of
2.9 ± 1.0 N·m (26 ± 8 lb in) . Install the three gaskets and plugs on the starting motor housing.Show/hide tableIllustration 12 g00706331 - Install the washer, the retainer, the boot, the spring, the retainer and the ring onto the plunger.
- Position the plunger assembly (10) into the shift lever housing. Install the nut finger tight. The plunger assembly will need to be adjusted for the correct pinion clearance after the starting motor has been completely assembled.
Show/hide table
Illustration 13 g00706338 - Position the solenoid (7) over the plunger assembly. Install the bolts (9) and tighten the bolts to a torque of
12.2 ± 2.7 N·m (108 ± 24 lb in) . Tighten the clamp. - Install the contact assembly (6). Install the insulator, the lockwashers, the washers, the nuts and the gasket onto the terminal assembly. Tighten the small nuts to a torque of
2.25 ± 0.25 N·m (20 ± 2.2 lb in) . Tighten the larger nuts to a torque of30 ± 3 N·m (22 ± 2 lb ft) . - Connect the leads (5) to the back of the terminal assembly (2). Install the terminal assembly, the bolts and the nuts onto the solenoid. Tighten the nuts to a torque of
2.25 ± 0.25 N·m (20 ± 2.2 lb in) . Connect the negative wire assembly to the ground terminal. Tighten the nut to a torque of30 ± 3 N·m (22 ± 2 lb ft) .
Caterpillar Information System:
Starting Motor - Delco 50-MT Starting Motor - Disassemble
Starting Motor - Delco 50-MT General Information
C9 Agricultural Engine for Challenger Tractors Engine Shutdown Is Intermittent
Starting Motor - Delco 50-MT Starting Motor Does Not Turn or Turns Slowly
Starting Motor - Delco 50-MT Pinion Clearance - Adjust
Starting Motor - Delco 50-MT No Load - Test
Starting Motor - Delco 50-MT Pinion Drive - Check
Starting Motor - Delco 50-MT Brush and Brush Holder - Check
345D, 349D and 349D2 Excavator Machine System Specifications Stick Cylinder Lines - Stick Lowering Control
Starting Motor - Delco 50-MT Armature - Test
Starting Motor - Delco 50-MT Field Winding - Test
Starting Motor - Delco 50-MT Starting Motor Solenoid - Test
3176C, 3406E and 3456 Industrial Engines Engine Stalls at Low RPM
C4.4 (Mech) Industrial Engine Crankcase Breather (Canister) - Replace
C3.4 IND Industrial Engine Engine Valve Lash - Inspect/Adjust
C4.4 and C6.6 Engines for Caterpillar Built Machines Fuel Rail Pump Solenoid - Test
C3.4 IND Industrial Engine Reference Material
C9 Agricultural Engine for Challenger Tractors Engine Top Speed Is Not Obtained
C3.4 IND Industrial Engine Maintenance Interval Schedule
Starting Motor - Delco 50-MT Normal Operation
C9 Agricultural Engine for Challenger Tractors Power Is Intermittently Low or Power Cutout Is Intermittent
TA19-M2WD and TA19-M4WD (Delta) Agricultural Transmission Power Train Electronic Control System Diagnostic Trouble Code List
C32 Marine Engines Fuel Filter Base - Remove and Install
Tightening Procedure for the Studs of the Variable Valve Actuator for 735 and 740 Articulated Trucks and C15 On-highway Truck Engine{1130} Tightening Procedure for the Studs of the Variable Valve Actuator for 735 and 740 Articulated Trucks and C15 On-highway Truck Engine{1130}