Electronic Control Module (ECM) - Configure
Show/hide table
Required Tools | ||
Part Number | Description | Quantity |
JEBD3003 | Caterpillar® Electronic Technician (Cat® ET) | 1 |
317-7484 | Communications Adapter III | 1 |
457–6114 | Data Link Cable Assembly | 1 |
Cat® Electronic Technician (Cat® ET) is used to access the configuration screen. A message on the screen will give instructions that guide the user through the procedure. Refer to the manual that is provided with the Cat® ET software for more information about Cat® ET.
A new electronic control module (ECM) must be configured when the ECM has been replaced. Configure the replacement ECM before a calibration is attempted.
A check of the configuration screen could resolve a problem with the machine. A problem with a component could be identified as one of the following items:
- The component is not installed.
- The component is installed but a change to the installation is needed to correct a problem.
Follow these instructions to get to the configuration screen:
- Connect the communications adapter and the computer to the diagnostic service tool connector.
- Start Cat ET.
Show/hide table
Illustration 1 g02623970 Typical Cat® ET Configuration screen - Select "File". Go to "Select ECM". Choose the "Transmission ECM".
- Go to the "Service" Menu. Select "Configuration". Click "OK". Certain operations or characteristics can be changed.
Caterpillar Information System:
Cat® Detect Object Detection System MID 134 - CID 3318 - FMI 11
Cat® Detect Object Detection System MID 134 - CID 3319 - FMI 11
Cat® Detect Object Detection System MID 134 - CID 3322 - FMI 11
Cat® Detect Object Detection System MID 134 - CID 3323 - FMI 11
Installation Procedure for 368-8120 Hydraulic Ar for 963D Track-Type Loaders{1408, 5057, 5133, 6129} Installation Procedure for 368-8120 Hydraulic Ar for 963D Track-Type Loaders{1408, 5057, 5133, 6129}
2011/06/27 An Improved Relay is Now Used on Certain Cat Products {4493}
D-Series and D2-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Access Doors and Covers
XQ400 Power Module Spark Plugs - Inspect/Adjust/Replace - Spark Plugs with Adjustable Electrode Gaps
Rework Procedure for 3E-5184 Secondary Steering Electronic Control Module {4348} Rework Procedure for 3E-5184 Secondary Steering Electronic Control Module {4348}
2011/07/11 The Paint Process Has Been Improved on Certain Components for D6T Track-Type Tractors {7000, 7559, 7581}
950K and 962K Wheel Loaders C7.1 Engine Supplement Air Cleaner - Remove and Install
950K and 962K Wheel Loaders C7.1 Engine Supplement Combustion Head - Remove and Install - Clean Emissions Module
994H Wheel Loader Electrohydraulic System Electronic Control Module (ECM) - Configure
621H, 623H and 627H Wheel Tractor-Scrapers Implement Electronic Control System Machine Inclination Sensing Device - Calibrate
950K and 962K Wheel Loaders Machine Systems Brake Control Valve (Service) - Remove and Install
854K Wheel Dozer and 992K Wheel Loader C32 Engine Supplement Transmission Oil Cooler Core - Remove and Install
D3K2, D4K2 and D5K2 Track-Type Tractors Engine Supplement Refrigerant Compressor
950K and 962K Wheel Loaders Machine Systems Steering Neutralizer Valve (Command Control Steering) - Remove and Install
950K and 962K Wheel Loaders C7.1 Engine Supplement Ignition Coil - Remove and Install - Clean Emissions Module
D3K2, D4K2 and D5K2 Track-Type Tractors Engine Supplement Engine Oil Pressure Sensor
D3K2, D4K2 and D5K2 Track-Type Tractors Engine Supplement Fuel Pressure Sensor
D3K2, D4K2 and D5K2 Track-Type Tractors Engine Supplement Boost Pressure Sensor
950K and 962K Wheel Loaders C7.1 Engine Supplement Flame Detection Temperature Sensor - Remove and Install - Flame Detection Temperature Sensor for the Combustion Head
910K and 914K Compact Wheel Loaders Battery or Battery Cable - Inspect/Replace