- Caterpillar Products
- Machines with Grease Lubricated Track with Swage
- Machines with Greased Lubricated Track (GLT)
- Machines with Positive Pin Retention (PPR) Track
- Machines with Positive Pin Retention 2 (PPR2) Track
- Machines with Rotating Bushing Track
- Machines with Sealed Positive Pin Retention (PPR) Track
- Machines with Sealed Track
- Machines with Sleeve Bearing Track
- Machines with non-PPR Sealed and Lubricated Track
- Machines with Greased Lubricated Track (GLT)
- Track Drills
- MD5150C (S/N: SEY1-UP)
Introduction
Revision | Summary of changes inSEBF8589 |
---|---|
15–19 | Added serial number prefixes for New Product Introduction. |
© 2019 Caterpillar All Rights Reserved. This guideline is for the use of Caterpillar dealers only. Unauthorized use of this document or the proprietary processes therein without permission may be violation of intellectual property law. Information contained in this document is considered Caterpillar: Confidential Yellow.
This Undercarriage Reconditioning Bulletin contains the necessary information to allow a dealer to establish a parts reusability program. Reuse and salvage information enables Caterpillar dealers and customers to benefit from cost reductions. Every effort has been made to provide the most current information that is known to Caterpillar. Continuing improvement and advancement of product design might have caused changes to your product which are not included in this publication. This Undercarriage Reconditioning Bulletin must be used with the latest technical information that is available from Caterpillar.
For technical questions when using this document, work with your Dealer technical Communicator (TC).
To report suspected errors, inaccuracies, or suggestions regarding the document, submit a form for feedback in the Service Information System (SIS Web) interface.
Canceled Part Numbers and Replaced Part Numbers
This document does not include all Canceled part number and replaced part number information. Use NPR on SIS for information about Canceled part numbers and replaced part numbers. NPR will provide the current part numbers for replaced parts.
Equipment
Description |
(1) Is equipment available, capable of cleaning the rollers prior to service? (Power washer or steam cleaner) |
(2) Is a workbench available, capable of holding 8 to16 rollers at an adequate height? (8 to16 is for efficiency, height is for quality) |
(3) Is tooling available, capable of removing plastic plugs, rubber stoppers, retainer bolts, retainer rings, and snap rings? |
(4) Is a hydraulic press available, capable of servicing rollers with press-on end collars, bushings, and end caps? |
(5) Is the available lighting adequate for inspecting the roller components? |
(6) Is a wash tank available for cleaning the roller components? (shafts, retainers, thrust washers, and seals) |
(7) Is a blast cabinet available to recondition the seal ramps on the shafts of inverted rollers? |
(8) Is an arbor press available for installing the Duo-Cone seals into the retainers and end collars? |
(9) Is tooling available to tighten the bolts to the proper torque? (Regulator, torque gun, torque wrench) |
(10) Is a pressure test available for testing the integrity of the roller? ( 170-5664 Test and Fill Cart Gp or FT-2724 Pressure Gauge Tool Gp) |
(11) Is a lubricator available for filling the roller to the proper oil fill volume? ( 170-5664 Test and Fill Cart Gp or portable lubricator) |
(12) Is equipment available to spin the shaft after assembly? |
Comments: |
Tooling and Accessories
Description |
(1) Are seal installers available for all models of rollers that are serviced? |
(2) Are the seal installers in good condition? (No chips or cracks) |
(3) Are lint free towels available for cleaning the roller components? (Duo-Cone seals, shafts, retainers, thrust washers) |
(4) Is 99% isopropyl alcohol available for lubricating the rubber toric rings for assembly? (Used with lint free towels) |
(5) Is 1U-6396 Petro Gel Grease (O-ring assembly compound) available for installing the O-rings? |
(6) Is tooling available to measure the clearance between the shaft and bearing, seal height, and end play? |
(7) Is clean oil available for lubricating the Duo-Cone seals and bearings? (Must be covered and free of contaminants) |
Comments: |
Literature
Description |
(1) Is Undercarriage Reconditioning Guide, SEBF8599 current and available to the mechanics and supervisors? |
(2) Are the roller wall charts current and available to the mechanics for easy accessibility? |
Comments: |
Training
Description |
(1) Have the supervisors and mechanics attended the Undercarriage Repair Process Training Class in Peoria? |
(2) Have the mechanics and supervisors been trained on reuse guidelines? |
Comments: |
Recommendations
Notes