Flywheel Housing - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Link Bracket | 2 |
Start By:
- Remove the combustion body group (ARD). Refer to Disassembly and Assembly, "Combustion Body Group (ARD) - Remove".
- Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Fasten Tooling (A) and a suitable lifting device to flywheel housing (1). The weight of flywheel housing (1) is approximately
25 kg (55 lb) .Show/hide tableIllustration 2 g01266373 - Remove bolts (2) and bolt (3). Remove bolts (4).
Show/hide table
Illustration 3 g01266377 - Remove bolts (5) that fasten the engine oil pan to flywheel housing (1). Remove flywheel housing (1).
Show/hide table
Illustration 1 | g01266372 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Link Bracket | 2 |
B | 1U-8846 | Sealant | - |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Apply Tooling (B) to the entire mounting face of the flywheel housing prior to installation.
Show/hide table
Illustration 4 g01266372 - Fasten Tooling (A) and a suitable lifting device to flywheel housing (1). The weight of flywheel housing (1) is approximately
25 kg (55 lb) . Position flywheel housing (1) on the cylinder block.Show/hide tableIllustration 5 g01266377 - Install bolts (5) that fasten the engine oil pan to flywheel housing (1).
Show/hide table
Illustration 6 g01266373 - Install bolts (4). Install bolt (3). Install bolts (2).
- Check the flywheel housing runout. Refer to the Testing and Adjusting, "Flywheel Housing - Inspect".
End By:
- Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
- Install the combustion body group (ARD). Refer to Disassembly and Assembly, "Combustion Body Group (ARD) - Install".
Caterpillar Information System:
TH48-E70 Petroleum Transmission Lifting and Tying Down the Transmission
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Configuration
C7 On-Highway Engine Clean Gas Induction Valve - Assemble
C13 Engine Air Compressor - Remove and Install
3500B Industrial Engines with the ADEM 3 Electronic Control Module Intermediate Speed Switch
C15 On-Highway Engine Fuel Filter Base
2006/07/01 A New Field Service Kit for Alternators is Now Available {1405, 7555}
C13 On-highway Engine Fuel Priming Pump
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Abbreviations and Acronyms
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Overview
C9 Marine Engines and C9 Marine Generator Sets Injection Actuation Pressure Sensor
C7 On-Highway Engine Air Inlet Cover - Remove and Install
C7 On-Highway Engine Coolant Temperature Sensor - Remove and Install
C7 On-Highway Engine Fuel Pressure Sensor - Remove and Install - Main
C9 On-highway Engine Electronic Unit Injector Wiring
C7 On-Highway Engine Fuel Pressure Sensor - Remove and Install - Pilot
3500B Industrial Engines with the ADEM 3 Electronic Control Module Overspeed Verify Switch
C13 Engine Crankshaft Position Sensor - Remove and Install
Mechanical Application and Installation Guide for TH48-E70 Petroleum Transmissions{3030, 3101} Mechanical Application and Installation Guide for TH48-E70 Petroleum Transmissions{3030, 3101}
C13 Engine Fuel Temperature Sensor - Remove and Install
C4.4 Industrial Engine Electronic Control System
3500B Industrial Engines with the ADEM 3 Electronic Control Module Permanent Timing Calibration Sensor
3044C Industrial Engine Refill Capacities and Recommendations
C9 On-highway Engine Air Compressor