Transmission and Scavenge Oil Pump - Assemble
组装步骤
Show/hide table
需要的工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-1861     | 挡圈钳     | 1     |
B     | 1P-1863     | 挡圈钳     | 1     |
C     | 1P-0510     | 冲头组件     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 清洁度是一项重要的因素。 组装之前,应彻底清洁所有零部件。 检查所有零件。 如果任何零件磨损或损坏,则应使用新件进行更换。 必须在清洁的工作面上及清洁的液压区域中进行所有的解体和组装步骤。 总是盖好并保护好清洁的零件。
注: 在组装之前必须先使用丝锥清理所有需要使用密封胶的螺纹。
注: 务必更换 O 形密封圈、密封垫和密封。 旧 O 形密封圈的密封性能可能不如新 O 形密封圈。 在组装过程中使用 1U-6396 O 形密封圈装配附着剂 。
注: 在组装之前先使用润滑剂润滑要密封的所有部件。
- 将轴承 (15) 安装到歧管 (1) 中。
Show/hide table
图 1 | g00766915 |
- 将齿轮 (13) 和齿轮 (14) 安装到歧管 (1) 中。
Show/hide table
图 2 | g00766912 |
- 使用工具 (C) 和适当的压具,将轴 (8) 安装到轴承 (12) 中。
Show/hide table
图 3 | g00766978 |
- 使用工具 (B) 安装挡圈 (11) 。
Show/hide table
图 4 | g00766903 |
- 将密封圈 (10) 安装到轴 (8) 上。
注: 在进行本步骤之前先使用润滑剂润滑要密封的密封。
- 将轴承 (9) 安装到盖 (6) 中。
Show/hide table
图 5 | g00766899 |
- 将轴组件 (8) 安装到盖 (6) 中。 然后将月牙键 (7) 安装到轴的键槽中。
- 将螺栓 (5) 和盖 (6) 安装到歧管 (1) 上。 拧紧螺栓至扭矩为 55 ± 10 N·m (41 ± 7 lb ft)。
Show/hide table
图 6 | g00766896 |
- 使用工具 (A) 安装挡圈 (4) 。
- 安装六角头螺钉 (2) ,将驱动齿轮 (3) 固定在齿轮泵上。
Show/hide table
图 7 | g00766887 |
(1) 歧管, (2) 六角头螺钉 和 (3) 齿轮 |
End By: 安装变速箱和扫油泵。 请参阅 解体和组装, "变速箱和扫油泵 - 安装"。
Caterpillar Information System:
TH31 Well Servicing Transmissions Transmission and Scavenge Oil Pump - Install
TH31 Well Servicing Transmissions Transmission and Scavenge Oil Pump - Remove
TH31 Well Servicing Transmissions Transmission Planetary - Assemble
C6.6 Engines for Caterpillar Built Machines Electronic Control System Components
2006/02/20 New Supplier for Glow Plugs {1412}
TH31 Well Servicing Transmissions Transmission and Scavenge Oil Pump - Disassemble
TH31 Well Servicing Transmissions Transmission and Torque Converter - Connect
3512B Oil Well Servicing Engine (ADEM III) Electrical Power Supply
C175 Generator Set Engines Idler Gears (Front) - Remove and Install
2006/01/02 New Bevel Gear And Pinions And Associated Components Provide Increased Service Life {3254, 3256}
EMCP3 MUI Engine Monitoring and Control
C6.6 Engines for Caterpillar Built Machines Fuel System
TH31 Well Servicing Transmissions Pump Drive - Assemble
C3.3 Industrial Engine Electric Starting Motor - Remove and Install
C3.3 Industrial Engine Fan - Remove and Install
C3.3 Industrial Engine Glow Plugs - Remove and Install - If Equipped
TH35 Well Servicing Transmissions Transmission Planetary - Assemble
3126B and 3126E Truck Engines Vibration Damper
The Valve Body May Crack on Certain Remanufactured Fuel Injectors{1290} The Valve Body May Crack on Certain Remanufactured Fuel Injectors{1290}
Installation of the Machine Security System (MSS) Universal Attachment Kit {7631, 7631} Installation of the Machine Security System (MSS) Universal Attachment Kit {7631, 7631}
C6.6 Engines for Caterpillar Built Machines Basic Engine
Reman Alternator Failures {1405} Reman Alternator Failures {1405}
C175-16 and C175-20 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
2006/01/02 A Different Grommet is Used to Secure the Engine Wiring Harness {1408}