- Wheel Loader:
- 966H (S/N: A6D1-UP)
- 972H (S/N: A7D1-UP)
Introduction
This service publication contains the installation information that is needed to install ride control on a field machine.
Personal injury or death can result from improper assembly procedures. Do not attempt any assembly until you have read and understand the assembly instructions. |
Personal injury or death can result from improper lifting or blocking. When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component. Approximate weights of the components are shown. Clean all surfaces where parts are to be installed. |
NOTICE |
---|
Do not allow any dirt or foreign material to get into the hydraulic system during assembly, connection of lines, when components are filled with fluid, or during any maintenance operation. |
A complete listing of the parts that are contained in these kits is listed in the Parts Manual, SEBC1471. This supplemental product support literature should be used with the appropriate Service Manual that is available for the standard machine.
Refer to Testing and Adjusting, RENR8858, "Ride Control Accumulator - Test and Charge" for charging instructions for the accumulator.
Do not perform any procedure and do not order parts that are outlined in this publication until you understand the information that is contained in this document.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide".
Dispose of all fluids according to local regulations.
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. |
Installation of the 290-3531 Ride Control Ar (KIT) for a Control Valve with Two Functions
Removal of Parts from the Main Valve
Note: Refer to Disassembly and Assembly, RENR8859, "Main Control Valve and Mounting Plate - Remove".
Note: Refer to Disassembly and Assembly, RENR8859, "Main Control Valve - Disassemble".
Note: Refer to Disassembly and Assembly, RENR8859, "Main Control Valve - Assemble".
Note: Refer to Disassembly and Assembly, RENR8859, "Main Control Valve and Mounting Plate - Install".
- Remove the following parts from the main control valve group:
- (A) Hose
- (B) Tube
- (C) Hydraulic block
- (A) Hose
Illustration 1 | g01303591 |
Control valve with two functions without ride control (A) Hose (B) Tube (C) Hydraulic block |
Installation of the 253-4026 Ride Control Valve Gp
- Install the following parts onto the main valve group:
Note: Regardless of the valve configuration, only the front section of the valve requires the Shuttle Valve to be replaced with a 183-7263 Plug As . All other valve sections require the shuttle valve to be installed.
Illustration 2 | g01319393 |
Main control valve |
Installation of the 246-2053 Ride Control Accumulator and Mounting Gp
- Use the following hardware and install the 246-2053 Ride Control Accumulator and Mounting Gp (7) :
Illustration 3 | g01319396 |
Right side view of ride control accumulator |
Note: Refer to Disassembly and Assembly, RENR8859, "Ride Control Accumulator - Remove and Install".
- Connect the other end of the 318-2606 Hose As (6) onto the 246-2053 Ride Control Accumulator and Mounting Gp (7) .
Installation of the 236-4612 Rocker Switch (Ride Control )
- Remove the plug and install the 236-4612 Rocker Switch (Ride Control) (9) .
Illustration 4 | g01319603 |
View of overhead console |
Installation of the 290-3531 Ride Control Ar (Kit) for a Control Valve with Three Functions
Removal of Parts from the Main Valve
Note: Refer to Disassembly and Assembly, RENR8859, "Main Control Valve and Mounting Plate - Remove".
Note: Refer to Disassembly and Assembly, RENR8859, "Main Control Valve - Disassemble".
Note: Refer to Disassembly and Assembly, RENR8859, "Main Control Valve - Assemble".
Note: Refer to Disassembly and Assembly, RENR8859, "Main Control Valve and Mounting Plate - Install".
- Remove the following parts from the main control valve group:
- (A) Hose
- (B) Tube
- (C) Hydraulic block
- (A) Hose
Illustration 5 | g01317745 |
Control valve with three functions without ride control (A) Hose (B) Tube (C) Hydraulic block |
Installation of the 253-4026 Ride Control Valve Gp
- Install the following parts onto the main valve group:
Note: Regardless of the valve configuration, only the front section of the valve requires the Shuttle Valve to be replaced with a 183-7263 Plug As . All other valve sections require the shuttle valve to be installed.
Illustration 6 | g01319393 |
Installation of the 246-2053 Ride Control Accumulator and Mounting Gp
- Use the following hardware and install the 246-2053 Ride Control Accumulator and Mounting Gp (7) :
Illustration 7 | g01317741 |
Right side view of ride control accumulator |
Note: Refer to Disassembly and Assembly, RENR8859, "Ride Control Accumulator - Remove and Install".
- Connect the other end of the 318-2606 Hose As (6) onto the 246-2053 Ride Control Accumulator and Mounting Gp (3) .
Installation of the 236-4612 Rocker Switch (Ride Control)
- Remove the plug and install the 236-4612 Rocker Switch (RIDE CONTROL) (9) .
Illustration 8 | g01319603 |
View of overhead console |
Accumulator Charging
- Refer to Testing and Adjusting, RENR8878, "Ride Control Accumulator- Test and Charge" in order to charge the ride control accumulator.
Software Configuration
Note: This is a configurable feature that must be activated. Refer to Testing and Adjusting, RENR8866, "Ride Control Configuration - Program" in order to configure this feature.
Note: The feature will be activated on the next power cycle.