Transmission Pump Drive Housing - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 8C-8422 | Sealant | 1 |
Note: Cleanliness is an important factor. Before installation, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Raise the temperature of gear (18). Use a suitable press to install bearing (19) in gear (18).
Show/hide table
Illustration 2 g00586283 - Install gear (18), bearing (19), and retaining ring (17) into housing (11).
Show/hide table
Illustration 3 g00586280 Show/hide tableIllustration 4 g00586607 - Install shaft (13), gear (14), and spacer (15) in housing (11).
- Use a suitable press to install bearing race (16) on shaft (13).
Show/hide table
Illustration 5 g00586276 - Install bolts (12) to shaft (13) and housing (11). Tighten bolts (12) to a torque of
55 ± 10 N·m (41 ± 7 lb ft) .Show/hide tableIllustration 6 g00586273 - Apply Tooling (A) to housing (11).
- Install housing (11) to the transmission cover.
- Install bolts (10). Tighten bolts (10) to a torque of
55 ± 10 N·m (41 ± 7 lb ft) .Show/hide tableIllustration 7 g00586271 - Lower the temperature of bearing (9). Use a suitable press to install bearing (9) in gear (8).
Show/hide table
Illustration 8 g00586269 - Install gear (8), bearing (9), and retaining ring (7) to cover assembly (4).
Show/hide table
Illustration 9 g01265134 - Install shaft (6) and bolts (5) in cover assembly (4). Tighten bolts (5) to a torque of
55 ± 10 N·m (41 ± 7 lb ft) . - Apply a continuous bead of Tooling (A) to the machined surface of cover assembly (4).
Show/hide table
Illustration 10 g00586264 - Install cover assembly (4) and bolts (3). Tighten the bolts to a torque of
55 ± 10 N·m (41 ± 7 lb ft) .Show/hide tableIllustration 11 g00586263 - Connect tube assembly (2) and install bolts (1). Tighten bolts (1) to a torque of
55 ± 10 N·m (41 ± 7 lb ft) .
Show/hide table
Illustration 1 | g00586603 |
End By:
- Install the transmission oil pump. Refer to Disassembly and Assembly, "Transmission Oil Pump - Install".
- Install the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Implement, Pilot, Steering, Brake) - Install".
- Install the bottom guard for the transmission. Refer to Disassembly and Assembly, "Bottom Guard (Transmission) - Install".
Caterpillar Information System:
525C, 535C and 545C Wheel Skidders Power Train Transmission Pump Drive Housing - Remove
D6G Series 2 Track-Type Tractor Power Train Brakes
938H Wheel Loader and IT38H Integrated Toolcarrier Steering System Secondary Steering Pump and Electric Motor
938H and IT38H Wheel Loader and Integrated Tool Carrier Power Train Transmission Oil Pump
2006/05/01 Inspection and/or Repair Procedure to Replace Crankshafts on Machine Engines {1202}
938H Wheel Loader and IT38H Integrated Toolcarrier Steering System Check Valve (Secondary Steering)
D6G Series 2 Track-Type Tractor Power Train Hydraulic Control Mechanism
525C, 535C and 545C Wheel Skidders Machine Systems Hydraulic Tank - Install
525C, 535C and 545C Wheel Skidders Machine Systems Hydraulic Tank - Remove
2006/06/05 New Speed Timing Sensor is Available {1912}
D6G Series 2 Track-Type Tractor Power Train Steering Clutch Hydraulic Control Valve
938H and IT38H Wheel Loader and Integrated Tool Carrier Power Train Temperature Sensor (Torque Converter Oil)
D7R Series II Track-Type Tractor Machine Systems Piston Motor (Steering) - Remove
2006/04/24 Correction to Specification , "D3C, D4C and D5C Series III Hystat Track-Type Tractor Power" {4350}
D7R Series II Track-Type Tractor Machine Systems Piston Motor (Steering) - Install
D11T, D8T and D9T Track-Type Tractors VIMSTM 3G / Product Link Electronic Control Module (ECM) - Replace
D7R Series II Track-Type Tractor Machine Systems Piston Motor (Steering) - Disassemble
C4.4 Industrial Engine Fuel Injection
D7R Series II Track-Type Tractor Machine Systems Piston Motor (Steering) - Assemble
631G Wheel Tractor-Scraper Power Train Speed Sensor (Transmission) - Assemble
The Breather Hole In 7T-7706 Housing As Is Not Drilled To the Correct Depth{3120} The Breather Hole In 7T-7706 Housing As Is Not Drilled To the Correct Depth{3120}
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Control Manifold (Implement, Steering Pump Margin Relief)
D7G2 Track-Type Tractor Power Train Sequence Relief Valve
525C, 535C and 545C Wheel Skidders Machine Systems Piston Pump (Implement, Steering, Brake) - Disassemble