Speed Sensor - Adjust
Show/hide table
Illustration 1 | g00937234 |
(1) Engine speed sensor |
Show/hide table
Illustration 2 | g01034314 |
(2) Torque converter output speed sensor |
Show/hide table
Illustration 3 | g00905794 |
(3) Transmission Intermediate Speed Sensors |
Show/hide table
Illustration 4 | g00937237 |
(4) Locknut
(5) Transmission Output speed Sensor |
- Remove transmission output speed sensor (5).
- Align one gear tooth with the speed sensor that is being set.
- Screw the sensor into the threaded hole by hand until the end of the sensor contacts the gear tooth.
- Back out the sensor by one-half turn (180 degrees in the counterclockwise direction). This sets the air gap to
0.71 mm (0.028 inch) . - Tighten locknut (4) to a torque of
25 ± 5 N·m (222 ± 45 lb in) .
Note: Do not allow sensor (5) to turn as locknut (4) is tightened.
Use this same procedure in order to adjust all speed sensors.
Note: There are six speed sensors. These sensors are listed in Table 1.
Show/hide table
Speed Sensors | ||
---|---|---|
Location | Output | Number of Sensors |
Transmission | Intermediate Speed | Two |
Transmission | Output Speed | Two |
Torque Converter | Output Speed | One |
Engine | Engine Speed | One |
In order to test the speed sensors, refer to the Service Manual, "Power Train Electronic Control System" for your machine.
Caterpillar Information System:
2002/06/03 Announcing the Combination of Groups Within the Paper Copies of the Caterpillar Parts Manuals {0374}
D5N Track-Type Tractor Power Train Priority Valve - Test and Adjust
D5N Track-Type Tractor Power Train Relief Valve (Torque Converter Inlet) Pressure - Test and Adjust
D6N Track-Type Tractor Power Train Relief Valve (Torque Converter Outlet) Pressure - Test and Adjust
2002/06/03 Underground Articulated Trucks are now Shipped with TDTO SAE 30W Oil {1000, 7000, 7581}
2002/06/03 New Clamps Improve Scavenge Pump Tube Service Life {3016, 3154}
D5N Track-Type Tractor Power Train Relief Valve (Transmission) - Test and Adjust
D6N Track-Type Tractor Power Train Pressure Charts
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Power Train Data Link
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 0096 - FMI 04
D5N Track-Type Tractor Power Train General Testing and Adjusting Information
D5N Track-Type Tractor Power Train Visual Inspection
D5N Track-Type Tractor Power Train Troubleshooting
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 0070 - FMI 04
IT28G Integrated Toolcarrier and 928G Wheel Loader Hydraulic System General Information
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 0177 - FMI 03
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 0177 - FMI 04
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 0426 - FMI 04
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 0473 - FMI 04
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 0177 - FMI 08
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 1401 - FMI 03
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 1402 - FMI 03
814F Wheel Dozer, 815F Soil Compactor and 816F Landfill Compactor Power Train MID 081 - CID 0168 - FMI 01
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders MID 081 - CID 1403 - FMI 03