Vibration Damper and Pulley - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 6V-9120     | Socket (1)     | 1 is     |
B     | 1P-2321     | Combination Puller     | 1     |
Show/hide table
( 1 ) | Tool (A) is a 46 mm socket. |
Start By:
- Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove six bolts (1) and the washers from vibration damper (2). Remove vibration damper (2) from crankshaft pulley (5) .
Note: Inspect the vibration damper for leaks and dents. If either condition exists, replace the vibration damper with a new part.
Show/hide table
Illustration 1 | g00528749 |
- Use Tool (A) and remove nut (3) and the washer from the crankshaft.
Show/hide table
Illustration 2 | g00559259 |
- If necessary, use Tool (B) and remove crankshaft pulley (5) .
Show/hide table
Illustration 3 | g00559308 |
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install crankshaft pulley (5) with the washer and nut (3) onto crankshaft (4) .
Show/hide table
Illustration 4 | g00559259 |
- Use Tool (A) to tighten nut (3) to a torque of 490 ± 10 N·m (360 ± 7 lb ft). Hit nut (3) with a hammer and torque the bolt again to 490 ± 10 N·m (360 ± 7 lb ft).
- Use six bolts (1) and the washers in order to install vibration damper (2) on the crankshaft pulley.
Show/hide table
Illustration 5 | g00528749 |
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Install".
Caterpillar Information System:
515 Wheel Skidder and 525 Wheel Skidder Hydraulic System Oil Filter - Replace
515 Wheel Skidder and 525 Wheel Skidder Transmission and Grapple Electronic Control System Glossary of Electrical Terms
963B Track-Type Loader Bucket Teeth and Cutting Edges - Inspect/Replace
994D Air System Wheel Loader Air Starting System
515 Wheel Skidder and 525 Wheel Skidder Hydraulic System Oil - Change
994D Air System Wheel Loader Control Valve (Air Tank Drain)
980G Wheel Loader Machine Systems Blower Motor (Air Conditioner, Heater) - Remove and Install
515 Wheel Skidder and 525 Wheel Skidder Hydraulic System Oil Level - Check
623F Wheel Tractor-Scraper Hydraulic System Floor Cylinder
623F Wheel Tractor-Scraper Power Train Torque Converter - Assemble
994D Air System Wheel Loader Relief Valve (Air Tank)
994D Air System Wheel Loader Solenoid Valve (Air Horn)
D9R Track-Type Tractor Steering Clutch and Brake Control
963B Track-Type Loader Radiator Pressure Cap - Clean/Replace
515 Wheel Skidder and 525 Wheel Skidder Transmission and Grapple Electronic Control System Electrical Connector - Inspect
515 Wheel Skidder and 525 Wheel Skidder Hydraulic System Oil Sample - Obtain
515 Wheel Skidder and 525 Wheel Skidder Transmission and Grapple Electronic Control System System Schematic
611 Wheel Tractor-Scraper Cooling System Pressure Cap - Clean/Replace
515 Wheel Skidder and 525 Wheel Skidder Engine Oil Level - Check
980G Wheel Loader Machine Systems Gear Pump (Hydraulic Fan) - Assemble
545 Wheel Skidder Hydraulic and Steering System Lift Cylinder (Decking Blade)
G3500B Engines Emergency Stopping
963B Track-Type Loader Cab Air Filter - Clean/Replace
623F Wheel Tractor-Scraper Machine Systems Steering Link - Remove and Install