Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1U-7234 | Feeler Gauge | 1 |
B | 5P-2986 | Protective Plate | 1 |
C | Gauge Bar | 1 | |
D | 1P-1862 | Pliers | 1 |
E | 1P-0510 | Driver Gp | 1 |
F | 5P-2989 | Retraction Plate | 1 |
G | 1P-0520 | Driver Gp | 1 |
- Thoroughly clean all parts prior to assembly. Put a small amount of clean hydraulic oil on all internal parts during assembly.
Show/hide table
Illustration 1 g00508592 - Heat bearing cone (18) to a maximum temperature of
120°C (248°F) . Use insulated gloves to handle the bearing cone. Put the bearing cone in position on shaft (17).Show/hide tableIllustration 2 g00508595 - Lower the temperature of bearing cup (11). Install the bearing cup in the head of the pump. Make sure that the cup is firmly seated against the shoulder.
Show/hide table
Illustration 3 g00508598 - Lower the temperature of bearing cup (31). Install the bearing cup in the pump body. Make sure that the cup is firmly seated against the shoulder.
- Perform the following procedure only if the shaft, the bearings, the head or the pump body are being replaced. Otherwise, proceed to Step 6.
Note: Do not install the barrel assembly or the pistons for this procedure.
- Heat bearing cone (13) to a maximum temperature of
120°C (248°F) . Use insulated gloves to handle the bearing cone. Put the bearing cone in position on shaft (17).Note: Make sure that any rotating parts are lubricated before you rotate the shaft.
- Install shaft (17) in the pump body.
- Install the gasket, the head and the bolts on the pump body.
- Put an 8S-2328 Dial Indicator Group in position in order to measure the axial movement of the shaft.
Note: Use a torque wrench to turn the shaft. The torque that is needed to start the rotation must not be more than
55 N·m (40 lb ft) . The torque that is needed to continue the rotation must not be more than37 N·m (27 lb ft) . - Rotate the shaft by 40 degrees in the clockwise direction and in the counterclockwise direction and zero the dial indicator.
- Apply
5340 N (1200 lb) of force on the end of the shaft. Rotate the shaft by 40 degrees in the clockwise direction and in the counterclockwise direction. Record the reading from the dial indicator. - Remove the force on the end of the shaft. Rotate the shaft by 40 degrees in the clockwise direction and in the counterclockwise direction. The reading on the dial indicator must be zero.
If the reading is not zero, repeat Steps 5.e through 5.g.
Note: The reading on the dial indicator must not exceed
0.36 mm (0.014 inch) . If the reading is less than0.05 mm (0.002 inch) , perform Steps 5.h through 5.l. If the reading exceeds0.33 mm (0.013 inch) , insert a0.25 mm (0.010 inch) shim between the head and the cover and repeat Steps 5.e through 5.g. - Remove the head and insert a
0.25 mm (0.010 inch) shim between the head and the pump body. Install the head and tighten the bolts. - Rotate the shaft by 40 degrees in the clockwise direction and in the counterclockwise direction and zero the dial indicator.
- Apply
5340 N (1200 lb) of force on the end of the shaft. Rotate the shaft by 40 degrees in the clockwise direction and in the counterclockwise direction. Record the reading from the dial indicator. - Remove the force on the end of the shaft. Rotate the shaft by 40 degrees in the clockwise direction and in the counterclockwise direction. The reading on the dial indicator must be zero.
If the reading is not zero, repeat Steps 5.i through 5.k.
Note: The reading on the dial indicator must be at least
0.28 mm (0.011 inch) . - Remove the head, the shims, the gasket and the shaft from the pump body.
- Remove bearing (13) from shaft (17).
Show/hide tableIllustration 4 g00508726 Show/hide tableIllustration 5 g00508124 Show/hide tableIllustration 6 g00508123 - Heat bearing cone (13) to a maximum temperature of
- Install spacer (24), spring (25) and spacer (26) in the barrel.
- Place barrel assembly (15) in a suitable press, as shown. Put Tooling (B) on the face of the barrel. Put Tooling (E) between the press and spacer (26).
- Use the press to compress spring (25). Use Tooling (D) to install snap ring (27).
Show/hide table
Illustration 7 g00508084 - Install wear plate (23) in the cam plate. Make sure that the dowel in the cam is aligned with the dowel hole in the wear plate.
Show/hide table
Illustration 8 g00508077 - Position pistons (19) on the wear plate in the correct sequence. Install retraction plate (22) over the pistons.
- Put the original amount of shims and bearings (21) on the cam and install bolts (20).
Show/hide table
Illustration 9 g00508892 - Use Tooling (A) to measure the clearance between the piston slippers and the wear plate.
The clearance between all of the piston slippers and the wear plate must be
0.090 ± 0.030 mm (0.0035 ± 0.0012 inch) . Change the amount of shims, as needed.Show/hide tableIllustration 10 g00508053 - Put Tooling (B) against the face of the barrel. Place barrel assembly (15) on Tooling (F), as shown. Install the pistons and cam (16) in the barrel assembly. Make sure that the pistons are installed in the original locations.
Show/hide table
Illustration 11 g00508935 - Install shaft (17), as shown.
Show/hide table
Illustration 12 g00508995 - Install one 3/8 inch - 16 NC guide bolt (32) in the cam plate. The length of the guide bolt must be
203 mm (8 inch) . Make sure that the dowel in the cam plate is aligned with the dowel hole in the pump body. - Use two persons to install the pump body over the shaft, as shown. The weight of the pump body is
36 kg (80 lb) .Show/hide tableIllustration 13 g00508325 - Install O-ring seals (30) on the retainer. Use Tooling (G) to install lip seals (29). Make sure that the sealing lips of both lip seals are facing outward.
Show/hide table
Illustration 14 g00509002 - Lubricate the seals on retainer (28) and install the retainer on the pump body, as shown. Remove guide bolt (32) and install three bolts (14) that secure the retainer to the pump body.
Show/hide table
Illustration 15 g00509066 Note: Do not scratch the polished surface of the barrel assembly. Pump efficiency will be reduced.
- Tilt the pump on Tooling (F). Keep Tooling (F) flat on the face of the barrel. Use a hoist to carefully place the pump on a clean work bench, as shown. The weight of the pump is
141 kg (310 lb) . Remove Tooling (F) and Tooling (B). - Heat bearing cone (13) to a maximum temperature of
120°C (248°F) . Use insulated gloves to handle the bearing cone. Put the bearing cone in position on shaft (17). Make sure that the bearing cone is firmly seated against the shoulder. - Install the gasket on the pump body.
Show/hide table
Illustration 16 g00507887 - Put a small amount of clean hydraulic oil on seal (12) and install the seal in the head.
Show/hide table
Illustration 17 g00507885 - Turn the head onto the opposite side and install port plate (10) in the head. Make sure that the dowels on the head are aligned with the dowel holes in the port plate.
Show/hide table
Illustration 18 g00509073 - Install two 1/2 inch - 13 NC guide bolts (3) through the bolt holes in the pump body. The length of the guide bolts must be
203 mm (8 inch) . Put head (9) in position on the pump body, as shown. - Install two bolts (2) with flat washers in order to hold the head tight against the pump body.
- Install original shims (8) and key (7) on the shaft.
Show/hide table
Illustration 19 g00509083 - Install impeller (6) and nut (5) on the shaft. The torque for the nut is
150 ± 20 N·m (110 ± 15 lb ft) . - Use Tooling (C) and Tooling (A) to check the clearance at 120 degree intervals around the impeller, as shown.
The clearance between the gauge bar and the impeller must be
0.44 ± 0.08 mm (0.017 ± 0.003 inch) . Use more shims (8) behind the impeller, if necessary. - Remove two bolts (2).
Show/hide table
Illustration 20 g00507835 Show/hide tableIllustration 21 g00507834 - Install the O-ring seal on cover (4). Install the cover on the head.
- Install bolts (2) in order to secure cover (4) to the head. Remove two guide bolts (3) and install the remaining bolts.
- Use a torque wrench to turn the shaft. The torque that is needed to start the rotation must not be more than
55 N·m (40 lb ft) . The torque that is needed to continue the rotation must not be more than37 N·m (27 lb ft) .Note: If the torque values are higher than the specifications, disassemble the pump and correct the problem.
End By:
- Install the fixed displacement pump. Refer to Disassembly and Assembly, "Piston Pump (Fixed Displacement) - Install".