Engine Oil Pan - Remove and Install
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
热油和热的部件可能会导致人员受伤。 不要让热的机油和部件接触皮肤。 |
- 将发动机机油排入合适的容器以便保存或弃置。 请参阅操作和保养手册 , "发动机机油 - 更换"。
Show/hide table
图 1 g01090963 - 拆下放油塞 (2) 和放油塞 ( 5)。 将 O 形密封圈从这些排放螺塞 ( 2) 和 (5) 上拆下。
- 拆下螺栓 (1)。 拆下发动机油底壳 ( 3)。
- 将隔离件密封 (4) 从缸体和发动机油底壳 ( 3) 上拆下。
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 8T-9022 | 硅胶密封垫 | - |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁发动机油底壳、缸体、前壳体和飞轮壳体的密封表面。
Show/hide table
图 2 g01090963 - 将隔离件密封 (4) 安装到发动机油底壳 ( 3) 上。
- 使用工具 (A) 以便填充飞轮壳体、缸体和发动机油底壳的空隙。 使用工具 (A) 以便填充前壳体、缸体和发动机油底壳的空隙。
- 将发动机油底壳 ( 3) 安放到位并安装螺栓 ( 1)。
- 安装 O 形密封圈和排放螺塞 ( 2)。 安装 O 形密封圈和排放螺塞 ( 5)。 拧紧排放螺塞 ( 2) 和 (5) 至扭矩为
70 ± 15 N·m (52 ± 11 lb ft) 。 - 加注发动机油底壳至发动机油尺上显示的正确油位。 请参阅操作和保养手册 , "发动机机油 - 更换"。
Caterpillar Information System:
G3520B Industrial Engine Oxygen Sensor Signal
G3520B Industrial Engine Oxygen Sensor Buffer Supply
3500B High Displacement Air Inlet and Exhaust Lines
G3520B Industrial Engine Oxygen Sensor - Calibrate
G3520B Industrial Engine Engine Speed/Timing Sensor - Calibrate
C27 and C32 Industrial and Petroleum Engines Intermittent Low Power or Power Cutout
2004/07/01 Some Older Mechanical Unit Injectors are Being Cancelled {1290}
3126E Truck Engines Maintenance Interval Schedule - Engines with a Deep Oil Sump
3126E Truck Engines Maintenance Interval Schedule - Engines with a Shallow Oil Sump
2004/10/01 Reduced Oil Change Intervals {7542}
2004/08/01 Special Instructions Are No Longer Announced In the Engine News {1000}
2004/08/01 Special Instructions Are No Longer Announced In the Truck Engine News {1000}
G3500B Engines Engine Oil Lines
G3406 Engines Cylinder Head Valves
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Oil Filter (Transmission)
3126E Truck Engines Reference Material
C4.4 (Mech) Industrial Engine Battery - Replace
C4.4 (Mech) Industrial Engine Battery or Battery Cable - Disconnect
C7 Marine Engines Fuel Cooler - Remove and Install
C7 Marine Engines Engine Sensors - Remove and Install
3500 Industrial Engines Auxiliary Water Pump
G3500 Engines Cooling System Coolant (NGEC) - Change
C15 and C18 Industrial Engines Flywheel Housing - Remove and Install
XQ125 Generator Set Driven Equipment - Check