Gear Pump (Secondary Steering) - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-0510     | 冲头总成     | 1     |
- 检查所有密封的状况。 如果任何密封磨损或损坏,则应使用新零件进行更换。 用清洁的液压油润滑密封。
注: 组装前,彻底清洁辅助转向泵的所有零件。
- 将清洁的液压油涂在辅助转向泵的所有内部零件上。
- 安装衬套 (27) ,使衬套从泵体组件 (6) 表面突出 5.6 至 5.8 mm (.22 至 .23 in)。
Show/hide table
注意 |
---|
不遵循建议的步骤或不使用这些步骤所需的指定工具会导致零部件损坏。 要避免零部件损坏,请使用建议的工具并遵循建议的步骤。 |
注: 泵壳体底部需要采用两个隔板。 泵壳体顶部需要采用两个隔板。 隔板将密封件固定在一起。 一个外径为圆边的隔板应置于泵壳体的底部。 圆边应朝下。 外径为直角边的隔板应靠近顶部法兰。
Show/hide table
图 1 | g00346246 |
- 将 O 形密封圈 (26) 安装到衬套 (27) 上。
- 将两个金属密封 (24) 和五个塑料密封 (25) 安装在泵体组件 (6) 中。
Show/hide table
图 2 | g00346244 |
Show/hide table
图 3 | g00346245 |
- 将板 (23) 安装在泵体组件 (6) 中。
Show/hide table
图 4 | g00346243 |
- 将齿轮 (22) 和轴 (21) 安装在泵体组件 (6) 中。
Show/hide table
图 5 | g00346242 |
- 将板 (20) 安装在泵体组件 (6) 中。
Show/hide table
图 6 | g00346241 |
- 将两个金属密封 (18) 和五个塑料密封 (19) 安装在泵体组件 (6) 中。
Show/hide table
图 7 | g00346239 |
Show/hide table
图 8 | g00346240 |
- 将环安装在法兰组件 (12) 中。 环开口应置于排放口上。 使用工具 (A) 安装两个唇形密封 (17) 。 组装密封,使弹簧加载件相互背离。
Show/hide table
图 9 | g00346237 |
- 将两个衬套 (15) 和两个定位销 (16) 安装在法兰组件 (12) 中。 衬套 (15) 应从法兰组件 (12) 的表面突出 5.6 至 5.8 mm (.22 至 .23 in)。
Show/hide table
图 10 | g00346236 |
- 将 O 形密封圈 (14) 安装到衬套 (15) 上。
Show/hide table
图 11 | g00346235 |
- 将密封 (13) 安装在法兰组件 (12) 上。
Show/hide table
图 12 | g00346234 |
- 将法兰组件 (12) 安装在泵体组件 (6) 的原始位置。 安装将法兰组件 (12) 固定至泵体组件 (6) 的垫圈和螺栓 (11) 。 螺栓的扭矩为 115 ± 5 N·m (85 ± 4 lb ft)。
Show/hide table
图 13 | g00346233 |
- 将两个密封 (10) 安装在泵体组件 (6) 上。
Show/hide table
图 14 | g00346232 |
- 将两个活塞 (8) 和两个弹簧 (9) 安装在泵体组件 (6) 中。
Show/hide table
图 15 | g00346191 |
- 将两个隔套 (7) 安装在隔套 (5) 中。
Show/hide table
图 16 | g00346190 |
- 将隔套 (5) 安装在泵体组件 (6) 中。
Show/hide table
图 17 | g00346189 |
- 将两个密封 (4) 安装在泵体 (2) 中。
Show/hide table
图 18 | g00346188 |
- 将两个活塞 (3) 和两个弹簧安装在泵体 (2) 中。
- 将泵体 (2) 安置在辅助转向泵的泵体组件上。 安装用于将泵体 (2) 固定至泵体组件的垫圈和螺栓 (1) 。 螺栓的扭矩为 115 ± 5 N·m (85 ± 4 lb ft)。
Show/hide table
图 19 | g00346187 |
End By: 安装辅助转向泵。 请参阅 拆解和组装, "辅助转向齿轮泵 - 安装"。
Caterpillar Information System:
Installation of D5M Sweep Group{7325} Installation of D5M Sweep Group{7325}
D11R Track-Type Tractor Hydraulic System Ripper Lift Cylinder
854G Wheel Dozer Steering Cylinder Bearings - Lubricate
611 Wheel Tractor-Scraper 3306B Engine Supplement Engine Front Support - Remove
D11R Track-Type Tractor Hydraulic System Bulldozer Tilt Cylinder
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Power Train Drive Shaft
611 Wheel Tractor-Scraper 3306B Engine Supplement Engine Front Support - Install
854G Wheel Dozer Machine Systems Gear Pump (Secondary Steering) - Disassemble
854G Wheel Dozer Machine Systems Gear Pump (Secondary Steering) - Install
D11R Track-Type Tractor Hydraulic System Bulldozer Lift Cylinder
854G Wheel Dozer Machine Systems Gear Pump (Secondary Steering) - Remove
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Engine Supplement Aftercooler - Remove and Install
627F Wheel Tractor-Scraper Stopping the Engine
D11R Track-Type Tractor Hydraulic System Ripper Tip Cylinder
D10R Track-Type Tractor Hydraulic System Pin Puller Cylinder
966G Wheel Loader and 972G Wheel Loader Engine Supplement Engine Oil Cooler - Remove and Install
966G Wheel Loader and 972G Wheel Loader Engine Supplement Transmission Oil Cooler - Remove
854G Wheel Dozer Machine Systems Relief Valve (Steering Pilot) - Remove and Install
D11R Track-Type Tractor Hydraulic System Quick Dump Valve
D11R Track-Type Tractor Hydraulic System Solenoid Valve (Pressure Control Override)
992G Wheel Loader Transmission Oil - Change
631E Series II Wheel Tractor-Scrapers Welding on Machines and Engines with Electronic Controls
854G Wheel Dozer Transmission Oil Filter - Replace
992G Wheel Loader Transmission Oil Level - Check