Fuel Manifold - Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component. |
- Install bolts (7) that hold fuel manifold (4) to the cylinder block.
- Install check valve (6) and tighten to a torque of
35 ± 3 N·m (26 ± 2 lb ft) . - Install the O-ring seal on fuel temperature sensor (1). Install the fuel temperature sensor on the fuel manifold and tighten to a torque of
20 ± 5 N·m (15 ± 4 lb ft) . - Connect the harness assembly for the fuel temperature sensor.
- Install the O-ring seal on fuel outlet temperature sensor (8). Install the fuel outlet temperature sensor on the fuel manifold and tighten to a torque of
20 ± 5 N·m (15 ± 4 lb ft) . - Connect the harness assembly for the fuel outlet temperature sensor.
- Connect hose assembly (5) to fuel manifold (4).
- Connect tube assembly (2) and tube assembly (3) to fuel manifold (4).
- Remove the air from the fuel system. Refer to Testing and Adjusting, "Fuel System - Prime".
Show/hide table
Illustration 1 | g01051618 |
Caterpillar Information System:
C18 Generator set and C18 Marine Engines Fuel Manifold - Remove
G3600 Engines Electrohydraulic System Oil - Change
3126B Marine Engines Engine Speed/Timing Sensor Circuit - Test
Installation Procedure for the New Drive Gears for the 3456 Engine{1206} Installation Procedure for the New Drive Gears for the 3456 Engine{1206}
C18 Generator set and C18 Marine Engines Turbocharger - Assemble
C18 Generator set and C18 Marine Engines Turbocharger - Disassemble
2004/05/31 Hose Kit Helps the Technician Properly Prepare Hydraulic Hose for Assembly {0684}
C-15 Petroleum Engine Fan Drive Bearing - Lubricate
C15 Petroleum Generator Set Engines Engine Oil Filter Base
2004/02/01 A Modification to the Air Inlet Cover Will Prevent the False Activation of a Diagnostic Event Code {1057, 1087, 5479}
2007/08/01 A New Joint Design is Introduced for the HEUI Fuel System's High Pressure Oil Pump {1307, 1714}
2004/02/01 A New Joint Design is Introduced for the HEUI Fuel System's High Pressure Oil Pump {1714}
G3612 and G3616 Engines Electrohydraulic System Oil Filter - Change
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - Parallel Cabinet Interface
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - AC Interface Board
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - DC Interface Board
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - Flywheel Interface Board
C7 Marine Engine Air Inlet and Exhaust System - Inspect
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - Static Switch Interface Board
G3600 Engines Engine Oil - Change
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - User Interface Board
3126B Marine Engines Engine Temperature Sensor Open or Short Circuit - Test
3126B Marine Engines Injector Solenoid Circuit - Test
C-10 Petroleum Engine Engine Oil Cooler