Water Pump - Assemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-0510 | 冲头总成 | 1 |
B | 138-9299(1) | 密封工具 | 1 |
488-2672(2) | 密封工具 | 1 | |
D | 139-0088(1) | 密封件安装工具 | 1 |
FT-3171(2) | 密封件安装工具 | 1 | |
F | 169-5464 | 快速固化底漆 | - |
Show/hide table
(1) | 与 |
(2) | 与 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 使用工具 (F) 清洁轴 (10) 和壳体 (4) 中油封 (5) 的沉头孔。
- 使用工具 (A) 将新油封 (5) 安装到壳体 (4) 中。 安装密封时使密封金属表面上的零件号朝向壳体。 确保油封与壳体沉头孔的前边缘平齐。 请勿润滑油封。
- 将轴承内圈 (6) 安装到轴 (10) 上。
- 安置轴承挡圈 (8),使 "本侧朝外" 标记朝向轴 (10) 的齿轮端。 安装齿轮 (15)。 将垫圈 (12) 和螺栓 (13) 安装到轴 (10) 上。 将螺栓 (13) 拧紧至扭矩为
215 ± 40 N·m (159 ± 30 lb ft) 。 - 在轴 (10) 上滑动工具 (B)。 锥边缘将朝向外侧。
- 将齿轮和轴组件安装到壳体 (4) 中。 小心不要损坏油封。 安装将轴承挡圈 (8) 固定在壳体上的螺栓 (14)。
- 从轴 (10) 上拆下工具 (B)。
- 使用工具 (D) 和适合的压具,将新的密封件 (2) 安装到轴 (10) 上和壳体 (4) 中。 确保密封外侧壳体完全座入壳体中。
- 将叶轮 (3) 定位到轴 (10) 上。 安装垫圈 (9) 和螺栓 (11)。 拧紧螺栓至扭矩为
39 ± 3 N·m (29 ± 2 lb ft) 。 - 将新的 O 形密封圈安装到适配器 (1) 的外侧。 利用干净的机油轻轻润滑密封。
- 将新的 O 形密封圈 (7) 安装到适配器 (1) 上。
- 将适配器 (1) 安置到壳体 (4) 上。
- 将新的 O 形密封圈 (16) 安装到壳体 (4) 中。
Show/hide table
图 1 | g01163722 |
结束:
- 安装水泵。
Caterpillar Information System:
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Install
C15 and C18 Engines for Caterpillar Built Machines Water Pump - Remove
C27 and C32 Generator Set Engines CID 0091 FMI 08 Throttle Position signal abnormal
Install the Correct Piston Cooling Jet and the Correct Retainer for the One-Piece Piston{1214, 1331} Install the Correct Piston Cooling Jet and the Correct Retainer for the One-Piece Piston{1214, 1331}
C9 Marine Auxiliary and Marine Generator Set Engines Low Power/Poor or No Response to Throttle
C15 and C18 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C7 Engine for 584 and 584HD Forwarders and for 525C, 535C, and 545C Wheel Skidders Intermittent Engine Shutdown
2004/01/01 A Special Instruction, REHS2060 , "Installation Instructions for the 240-0717 Engine Oil Lines Gp for the Hydraulic Electronic Unit Injector (HEUI) Pump" is Available {1307, 1714}
2006/06/26 Some Pistons and Cylinder Packs are Cancelled and Replaced {1214}
2004/05/03 New Hydraulic Hose Assembly Machine Integrates Crimputer II with Radial Crimping Technology {0738}
C18 Marine Auxiliary Engines Engine Pressure Sensor Open or Short Circuit - Test
3126B Industrial Engine Electronic Control Module - Remove and Install
C18 Marine Auxiliary Engines Event Codes
C18 Marine Auxiliary Engines Diagnostic Codes
G3500 Engines Control Module Self Test
2004/01/01 A New Spring for the Oil Filter Bypass Valve and for the Oil Cooler Bypass Valve is Now in Production {1306, 1314, 1318, 1378}
2004/03/01 A New Spring for the Oil Filter Bypass Valve and for the Oil Cooler Bypass Valve is Now in Production {1306, 1314, 1318, 1378}
C18 Marine Generator Set Engines CID 1929 FMI 03 Fuel Return Temperature Sensor voltage high/short to +batt
C18 Marine Generator Set Engines CID 1929 FMI 04 Fuel Return Temperature Sensor voltage low/short to ground
C13, C15, and C18 Generator Set Engines E368 High Intake Manifold Air Temperature
C18 Marine Auxiliary Engines Sensors and Electrical Connectors
C13, C15, and C18 Generator Set Engines E009 High Altitude Derate
Troubleshooting Tips Will Help Maintain Steady Engine RPM{1264, 1280} Troubleshooting Tips Will Help Maintain Steady Engine RPM{1264, 1280}