Air Compressor - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 138-7573 | 连杆支架 | 1 |
Show/hide table
不要断开空气管路,直到系统中的空气压力为零。 如果在压力下断开软管的话,可能会造成人身伤害。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 从空气罐中释放空气压力,并从冷却系统中排空冷却液。
Show/hide table
图 1 g01028440 - 将软管组件 (1) 和软管组件 (3) 从空气压缩机上断开。
- 将软管组件 (2) 和软管组件 (4) 从空气压缩机上断开。
- 将工具 (A) 和适当的起吊设备固定到空气压缩机上。 空气压缩机的重量约为
23 kg (51 lb) 。 - 利用以下程序拆下空气压缩机的安装支架:
- 拆下将安装支架固定到空气压缩机上的螺栓 (5)。
- 拆下用来将安装支架固定到缸体上的螺栓 (6)。 拆下空气压缩机的安装支架。
Show/hide table图 2 g01028442 Show/hide table图 3 g01028444 - 从正时齿轮壳体上拆下螺栓 (7)、空气压缩机 (8) 和一体式密封件。
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 138-7573 | 连杆支架 | 1 |
B | 9S-3263 | 螺纹锁固胶 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将工具 (A) 和适当的起吊设备安装到空气压缩机上。 空气压缩机的重量约为
23 kg (51 lb) 。 - 检查一体式密封件的状况。 必要时,更换一体式密封件。 将一体式密封件安装在空气压缩机 (8) 和正时齿轮壳体之间。
- 将空气压缩机 (8) 定位到前壳体内。 确保驱动齿轮与前壳体内的齿轮正确啮合。
- 将工具 (B) 涂抹在螺栓 (7) 的螺纹上。 安装螺栓 (7)。 拧紧螺栓 (7) 至
100 ± 20 N·m (75 ± 15 lb ft) 的扭矩。 - 利用以下程序安装空气压缩机的安装支架:
- 定位空气压缩机的支架并用手带紧螺栓 (5) 和螺栓 (6)。
Show/hide table
注意 压缩机支架松动可导致前端盖破裂和发动机前齿轮系损坏。
- 拧紧螺栓 (5) 至
60 ± 12 N·m (44 ± 9 lb ft) 的扭矩。 拧紧螺栓 (6) 至扭矩为60 ± 12 N·m (44 ± 9 lb ft) 。 拆下适当的起吊设备和工具 (A)。
Show/hide table图 5 g01028442 Show/hide table图 6 g01028440 - 定位空气压缩机的支架并用手带紧螺栓 (5) 和螺栓 (6)。
- 将软管组件 (4) 连接到空气压缩机上。 如有必要,将用来固定软管组件 (4) 的管夹连接到空气压缩机上。 将用来固定机油软管组件管夹的螺栓拧紧至
28 ± 7 N·m (21 ± 5 lb ft) 的扭矩。 - 将软管组件 (1) 和软管组件 (3) 连接至空气压缩机上。
- 将软管组件 (2) 连接到空气压缩机上。
- 向冷却系统加注冷却液到正确的液位。 请参阅操作和保养手册,了解正确的加注程序。
Show/hide table
图 4 | g01028444 |
Caterpillar Information System:
C11 and C13 Engines for Caterpillar Built Machines E361 High Engine Coolant Temperature
C11 and C13 Engines for Caterpillar Built Machines E539 High Intake Manifold Air Temperature
C11 and C13 Engines for Caterpillar Built Machines E360 Low Engine Oil Pressure
2003/10/01 Improved Water Pump Seal {1361}
C11, C13 and C15 On-highway Engines Selected Engine Rating
C13 and C15 On-highway Engines Multi-Torque - Test
C11, C13 and C15 On-highway Engines Output Selections
C7 and C9 On-Highway Engines Two Speed Axle Switch Circuit - Test
2003/10/01 Correct Lash Setting for the Fuel Injector {1290}
C9 Marine Engines and C9 Marine Generator Sets Housing (Front) - Install
C9 Marine Engines and C9 Marine Generator Sets Housing (Front) - Remove
C11 and C13 Engines for Caterpillar Built Machines E390 Fuel Filter Restriction
2003/10/01 New Fuel Lines Help to Eliminate Damage from Rubbing {1274}
C9 Marine Engines and C9 Marine Generator Sets Flywheel - Remove
C9 Marine Engines and C9 Marine Generator Sets Flywheel - Install
C7 On-highway Engine Fuel Priming Pump - Remove and Install
C7 On-highway Engine Fuel Filter Base - Remove and Install
C7 On-highway Engine Engine Oil Cooler - Remove
C7 On-highway Engine Engine Oil Cooler - Install
G3500H 60Hz Generator Sets Water Pump - Inspect
C7 PETROLEUM Petroleum Engine Crankshaft Front Seal - Remove
C7 PETROLEUM Petroleum Engine Crankshaft Front Seal - Install
EMCP3 General Information
2003/10/01 A New Cylinder Head Group For G3408 Engines {1100}