Camshaft Idler Gear - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-0520     | 起子总成     | 1     |
开始:
- 拆下前壳体。 请参阅拆解和组装, "壳体(前) - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下螺栓 (4) 和挡板 (1) 。
Show/hide table
图 1 | g01125301 |
- 卸下凸轮轴惰轮 (2) 。
- 从缸体拆卸螺栓 (7) 和惰轮轴 (3) 。 拆卸止推片 (5) 。
- 利用工具 (A) 和适当的压具将轴承 (6) 从凸轮轴惰轮 (2) 上拆下。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-0520     | 起子总成     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 和合适的压具在凸轮轴惰轮 (2) 上安装轴承 (6) 。 安装轴承,使轴承低于凸轮轴惰轮 (2) 前端面 1.080 ± 0.250 mm (0.0425 ± 0.0098 in)。
Show/hide table
图 2 | g01125304 |
- 将止推片 (5) 和惰轮轴 (3) 安置在缸体上。 安装螺栓 (7) 。 拧紧螺栓至扭矩为 70 ± 15 N·m (51 ± 11 lb ft)。
- 在惰轮轴 (3) 上安装凸轮轴惰轮 (2) 。 确保正时标记 (8) 朝外。 使正时标记 (8) 与曲轴驱动齿轮 (10) 上的正时标记 (9) 对准。
- 安置板 (1) ,安装螺栓 (4) 。 将螺栓拧紧至扭矩为 70 ± 15 N·m (51 ± 11 lb ft)。
End By: 安装前壳体。 请参阅 拆解和组装, "壳体(前) - 安装"。
Caterpillar Information System:
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Install
C15 On-highway Engine Pistons and Connecting Rods - Remove
C15 and C18 Generator Set Engines Connecting Rod Bearings - Remove
C15 On-Highway Engine Crankshaft - Install
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Disassemble
C15 On-Highway Engine Pistons and Connecting Rods - Assemble
C15 On-Highway Engine Camshaft - Remove
C15 On-Highway Engine Camshaft - Install
C15 and C18 Generator Set Engines Connecting Rod Bearings - Install
C15 and C18 Generator Set Engines Crankshaft Main Bearings - Remove
C15 On-Highway Engine Crankshaft - Remove
C15 and C18 Generator Set Engines Crankshaft Main Bearings - Install
3126E and 3126B Commercial and Truck Engines Federal Emission Control Warranty
3516B HD Generator Set Engine Mounts - Check
G3304 and G3306 Engines Engine Oil Pump - Install
C7 Engines for Combat and Tactical Vehicles Data Link Parameters
G3304 and G3306 Engines Engine Oil Pump - Disassemble
C7 Engines for Combat and Tactical Vehicles Dedicated PTO Parameters
C7 Engines for Combat and Tactical Vehicles Engine/Gear Parameters
3126E and 3126B Commercial and Truck Engines California Emission Control Warranty Statement
C7 Engines for Combat and Tactical Vehicles Engine Monitoring Parameters
C15 On-highway Engine Engine Oil Cooler - Remove
3500B Series II Marine Engines MID 036 - CID 0253 - FMI 02 Personality Module mismatch
3500B Series II Marine Engines MID 036 - CID 0254 - FMI 12 Electronic Control Module Error