Crankshaft Front Seal - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 9U-6210     | 前油封安装工具     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 本步骤适用于壳体(前)仍在发动机上的情况。 如果从发动机上拆下了壳体(前),不要遵循本步骤。 如果从发动机上拆下了壳体(前),请参阅拆解和组装手册, "壳体(前)- 安装"。
- 清洁油封壳体 (8) ,然后检查油封壳体有无损坏。 如有必要,更换壳体(前)。 请参阅拆解和组装手册, "壳体(前)- 拆卸和壳体(前)- 安装"。
- 检查皮带轮和曲轴前油封的接触面有无磨损。 如有必要,修理曲轴皮带轮。 有关详细信息,请参阅拆解和组装手册, "曲轴耐磨衬套(前)- 拆卸和曲轴耐磨衬套(前)- 安装"。
注: 新曲轴前油封 (6) 上连接有一个衬套 (5) 。 此时请勿拆下衬套 (5) 。 如果新曲轴前油封上没有安装衬套 (5) ,废弃新曲轴前油封 (6) 。
- 将紧固盘 (7) 安装到曲轴前部。 将螺母 (1) 和压力盘 (2) 安装到螺纹杆 (3) 上。
注: 不要润滑曲轴前油封 (6) 。 不要润滑油封壳体 (8) 。
Show/hide table
图 1 | g01148784 |
工具 (A) 中含有部件 1、2、3、4、7 和 9。 |
- 将衬套组件 (5) 和曲轴前油封 (6) 与油封壳体 (8) 的前部对齐。
Show/hide table
注意 |
---|
确保弹簧加载式曲轴前油封的唇缘朝向前壳体的内侧,并且正好位于曲轴前油封使用的壳体孔中。 |
- 将接头 (4) 安装到衬套 (5) 上。
- 将压力盘 (2) 安装到接头 (4) 上,再将螺纹杆 (3) 拧到紧固盘 (7) 上。 检查组件和曲轴前油封 (6) 与油封壳体 (8) 是否对齐。
- 将适当的杆经孔 (9) 插入螺纹杆 (3) 中,以防拧紧螺母 (1) 时螺纹杆转动。 拧紧螺母 (1) ,以便将曲轴前油封 (6) 推到油封壳体 (8) 中。 继续拧紧螺母 (1) ,直到接触到油封壳体 (8) 的底面。
- 逆时针转动衬套 (5) ,同时拉动衬套,以便从油封壳体 (8) 上取下衬套。 拆下接头 (7) 。
- 立即安装曲轴皮带轮。 请参阅拆解和组装手册, "曲轴皮带轮 - 拆卸和安装"。
Caterpillar Information System:
3054E Industrial Engine Crankshaft Front Seal - Remove
C13, C15, and C18 Tier 4 Final Engines Housing (Front)
3054E Industrial Engine Crankshaft Pulley - Remove and Install
C13 Engine for Combat and Tactical Vehicles Flywheel Housing
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Ethernet Interface
C1.5 and C2.2 Generator Sets Generator Lead Connections
C13, C15, and C18 Tier 4 Final Engines Gear Group (Front)
3054E Industrial Engine Crankshaft Rear Seal - Install
C11 and C13 Engines Piston Cooling Jet
3054E Industrial Engine Camshaft - Remove and Install
C9 Marine Engines Sensors and Electrical Connectors
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Fan Override Switch Circuit - Test
C13 and C15 Engines for Combat and Tactical Vehicles Remote PTO Accelerator Position Sensor Circuit - Test
320B, 320B L and 320B N Excavators Swing Drive Oil Sample - Obtain
3054E Industrial Engine Piston Cooling Jets - Remove and Install
3054E Industrial Engine Fuel Priming Pump and Fuel Filter Base - Remove and Install
2003/02/03 Special Instruction, REHS1238, "Obtaining Factory Passwords and Software Enabled Attachments" is Available {7610}
C1.5 and C2.2 Generator Sets Voltage Regulators
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Service Brake Pedal Position (Switch 1) Circuit - Test
C11 and C13 On-Highway Engines Belt Tensioner
3054E Industrial Engine Engine Oil Filter Base - Remove and Install
3054E Industrial Engine Engine Oil Cooler - Remove
3054E Industrial Engine Engine Oil Cooler - Install
C13, C15, and C18 Tier 4 Final Engines Water Pump