Exhaust Manifold
Show/hide table
图 1 | g01275256 |
使用以下步骤来安装排气歧管和波纹管:
- 将歧管安装到缸盖。 使用 5P-3931 防咬合剂 润滑螺栓螺纹,然户用手拧紧螺栓。
注: 为避免损坏波纹管,请单独装配与拆卸排气歧管段。 可从法兰的任意一侧装配波纹管的螺栓和螺母。
- 将波纹管安装到歧管。 使用 5P-3931 防咬合剂 润滑波纹管的螺栓螺纹。 拧紧波纹管的螺栓。
扭矩 ... 55 ± 10 N·m (41 ± 7 lb ft)
- 拧紧将歧管固定到缸盖的螺栓。
- 拧紧其余的波纹管螺栓。
扭矩 ... 55 ± 10 N·m (41 ± 7 lb ft)
(1) 螺栓
-
使用 5P-3931 防咬合剂 润滑螺栓螺纹。
- 扭矩 ... 240 ± 40 N·m (180 ± 30 lb ft)
(2) 管塞
-
使用 5P-3931 防咬合剂 润滑管塞螺纹。
- 扭矩 ... 130 ± 20 N·m (95 ± 15 lb ft)
(3) 排气歧管
(4) 波纹管
(5) 管塞
-
使用 5P-3931 防咬合剂 润滑管塞螺纹。
- 扭矩 ... 130 ± 20 N·m (95 ± 15 lb ft)
(6) 适配器
-
使用 5P-3931 防咬合剂 润滑适配器螺纹。
- 扭矩 ... 200 ± 25 N·m (150 ± 18 lb ft)
(7) 适配器
-
使用 5P-3931 防咬合剂 润滑适配器螺纹。
- 扭矩 ... 200 ± 30 N·m (150 ± 22 lb ft)
Caterpillar Information System:
G3500 Engines Vibration Damper Guard
C4.4 (Mech) Industrial Engine Electric Starting System - Test
3126E Truck Engine Electrical System
2002/12/01 A New Top Piston Ring Promotes Reduced Cylinder Liner Wear {1214, 1215}
3126B Marine Engines Transmission Oil Temperature Sensor Open or Short Circuit - Test
3056E Industrial Engine Pistons and Connecting Rods - Install
3056E Industrial Engine Pistons and Connecting Rods - Assemble
3056E Industrial Engine Pistons and Connecting Rods - Disassemble
3056E Industrial Engine Pistons and Connecting Rods - Remove
3406E, C12, C15 and C18 Marine Engines Engine Pressure Sensor Open or Short Circuit - Test
3056E Industrial Engine Connecting Rod Bearings - Install
3056E Industrial Engine Connecting Rod Bearings - Remove
3126E Truck Engine Basic Engine
3126E Truck Engine Vibration Damper - Check
3056E Industrial Engine Air Inlet Heater - Remove and Install
C7 On-highway Engine Valve Mechanism Cover
3126E Truck Engine Engine Oil Pressure Sensor - Test
G3606 and G3608 Engines Exhaust Manifold
G3606 and G3608 Engines Exhaust Manifold
3126E Truck Engine Air Inlet and Exhaust System - Inspect
3056E Industrial Engine Valve Guide - Inspect
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0052-11 Air Inlet Shutoff Shutdown (00)
3054E Industrial Engine Voltage Load Protection Module - Remove and Install
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Component Location - System Cabinet