Crankshaft Main Bearings - Remove
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 8T-0960 | 处理工具总成 | 1 |
B | 191-5323 | 油缸总成 | 2 |
191-5326 | 衬套 | 2 | |
C | 191-5335 | 支架 (主轴承) | 2 |
D | 191-5347 | 液压泵 (气动) | 1 |
229-9453 | 附件总成 (油泵) | 1 | |
E | 134-0932 | 主轴承冲头 | 1 |
F | 4C-9818 | 六角适配器(1) | 1 |
4C-9819 | 万向节(1) | 1 | |
213-3110 | 套筒(1) | 1 | |
4C-9927 | 钻孔机(1) | 1 |
Show/hide table
(1) | 此工具可用于转动发动机。 |
开始:
- 卸下曲轴箱盖。 请参阅拆解和装配, "曲轴箱盖 - 拆卸和安装"。
- 拆卸曲轴箱防爆安全阀。 请参阅拆解和装配, "曲轴箱防爆安全阀 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 从发动机的两侧卸下鞍座螺栓 (1)。
Show/hide table
图 2 g00929941 - 将工具 (A) 连接至发动机。
- 将工具 (B) 连接到工具 (A) 上。
Show/hide table
图 3 g00929996 Show/hide table图 4 g00929946 - 将工具 ( C) 定位至螺柱 ( 2 )上。
- 将工具 ( B) 安装至螺柱 (2 )上。 当螺柱 (2) 上的工具 (B) 过紧时,将工具 (B) 回旋 1/2 圈。
Show/hide table
图 5 g00929950 - 将工具 (D) 安装至工具 (B) 上。
- 必须正确定位工具 (C) 上的槽,以便为曲轴提供间隙。 参考图 5。
- 对于另一个螺柱,请重复步骤 2 至 8。
Show/hide table
图 6 g00929952 Show/hide table图 7 g00955701 典型示例 - 固定工具 (D) 以实现
108.0 ± 4.0 MPa (15670 ± 573 psi) 。 对工具 (B) 施压时,请将螺母 (3) 拧松至少 1.5 圈。 请参阅发动机信息, "SEBD9405 3600、C280 和 G3600 发动机螺柱张紧工具总成要求不同液压压力"。注: 对工具 (B) 施压时,如果红色标记 (X) 暴露在外,那么工具 (B) 处于最大行程。 释放工具 (B) 的压力,然后重复步骤 5 至 9。 未能释放压力可能会导致工具 (B) 损坏,或不能拧松螺母 (3)。
- 拆下工具 (B)、工具 (C) 和工具 (D)。
Show/hide table
图 8 g00955370 - 为协助维修人员,请使用位置 (Y) 上工具 (A) 的孔。
Show/hide table
图 9 g00955399 - 将工具 (A) 上的连杆连接至主轴承盖 (4) 上工具 (A) 上的销。
- 使用工 (A) 固定主轴承盖 (4),以便卸下螺母 (3) 和垫圈。
- 小心地降低工具 (A) 托盘上的主轴承盖 (4)。 如有必要,用橡皮锤敲击主轴承盖 (4),以便松开轴承盖 (4)。
- 从主轴承盖 (4) 上卸下主轴瓦 (5)。 在下主轴瓦 (5) 上标记识别号。
Show/hide table
图 10 g00955401 - 使用工具 (E) 可以滚出上主轴瓦 (6)。
注: 上主轴瓦 (6) 上有一个定位销。 从飞轮方向观察上主轴瓦 (6) 时,顺时针转动方可卸下上主轴瓦 ( 6)。
Show/hide table图 11 g00955402 - 将工具 (E) 安装在主轴承轴颈内的润滑孔中。 顺时针方向转动曲轴。
- 卸下上主轴瓦 (6)。 在上主轴瓦 (6) 上标记识别号。
Show/hide table
图 12 g00955403 - 卸下主轴承盖 (4) 后,卸下前止推片和后止推片。 小心地撬起曲轴,以便止推片 (7) 滚出缸体。
- 检查下主轴瓦、 (5)、上主轴瓦 (6) 和止推片 (7) 是否损坏。
Show/hide table
图 1 | g00955369 |
Caterpillar Information System:
3054E Industrial Engine Electrical System
G3520C and G3520E Generator Set Engines Manifold Air Pressure Sensor
C-15 and C-16 Industrial Engines Summary of Revisions
G3500B Engines Engine Governing - Adjust
G3520C and G3520E Generator Set Engines General Information (Electronic Control System)
2002/11/04 Connecting Rods with Dual Bearing Tab Slots are OK to Use {1218}
C4.4 (Mech) Industrial Engine Lubrication System
C4.4 (Mech) Industrial Engine Cooling System
2002/10/01 Parts Manuals For The Following Engines Are Now Provided On A CD-ROM {1000, 7000}
2002/11/01 A New Water Tank Group Is Used To Contain The Overflow Of Coolant {1354, 1377}
Product Link 151/201 Reporting Interval Erratic
Product Link 151/201 Operating Hours Discrepancy
G3520C and G3520E Generator Set Engines Detonation Sensor
G3520C and G3520E Generator Set Engines Ignition Transformer
3054E Industrial Engine Fuel Injection
3054C Industrial Engine Fuel Related Components in Cold Weather
3054E Industrial Engine Electronic Control System
3516B Generator Set Engines with Dynamic Gas Blending General Information (Fuel System) - Gas
3054C Industrial Engine Refill Capacities
C9 Marine Engines and C9 Marine Generator Sets Heat Exchanger
C7 Urban Transit Bus Engines Fire Prevention and Explosion Prevention
G3520C and G3520E Generator Set Engines Camshaft Timing
C9 On-highway Engines Starting the Engine
G3520C and G3520E Generator Set Engines Measuring Inlet Manifold Temperature