Starting Motor - Disassemble - 42-MT
Disassemble the Starting Motor
Note: The disassembly and assembly that follows is of the 24 volt starting motor. The 12 volt is similar.
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Quantity     |
A     | 1P-1855     | Retaining Ring Pliers     | 1     |
B     | 1P-0510     | Driver Gp     | 1     |
- Disconnect wire assembly (4) from solenoid (1). Disconnect motor terminal connector (3) from the starting motor housing.
Show/hide table
Illustration 1 | g00810559 |
- Remove three bolts (2) from the shift lever housing. Do not disassemble the solenoid. The parts inside the solenoid are not serviceable.
- Remove the O-ring seal and bushing (5) .
Show/hide table
Illustration 2 | g00818016 |
- Remove the nut (6). Remove the solenoid from the shift lever housing.
Show/hide table
Illustration 3 | g00810580 |
- Remove the negative terminal nuts "-", wire assembly (2), and washers. Remove six bolts (8) and rear housing (7) .
Show/hide table
Illustration 4 | g00810574 |
- If necessary, remove bushing (9) from the rear housing.
Show/hide table
Illustration 5 | g00818558 |
- Remove washer (12) from the armature shaft. Lift brush springs (10) and pull the brushes away from the commutator. Position the brush springs (10) on the side of the brushes in order to hold the brushes in the holders.
Show/hide table
Illustration 6 | g00810576 |
- Disconnect field winding leads (13) from brush holder (11). Remove the brush holder.
- Remove brushes (15) and negative "-" terminal (14) from the brush holders.
Show/hide table
Illustration 7 | g00818538 |
- Scribe a line on the pinion drive, the shift lever and the starting motor housings for the correct alignment at assembly.
Show/hide table
Illustration 8 | g00810579 |
- Remove six bolts (17) and pinion drive housing (16) .
- Remove retainer (18) with tool (A). Remove shift lever pin (20). If necessary, remove the O-ring seals from the shift lever pin.
Show/hide table
Illustration 9 | g00810582 |
- Remove pinion drive (19) and the shift lever.
- Remove the brake disc from the armature shaft. Remove five bolts (22), shift lever housing (21) and the washer. If necessary, remove the outside O-ring seals.
Show/hide table
Illustration 10 | g00810585 |
- If necessary, remove the seal and the bushing from the shift lever housing.
- Remove armature (22) from the starting motor housing.
Show/hide table
Illustration 11 | g00810588 |
- Remove the following components from the starting motor housing: eight screws (26), pole shoes (25) and field winding coil (24). It may be necessary to use an impact driver to remove screws (26) .
Show/hide table
Illustration 12 | g00810589 |
- Clean the armature, field winding coil and pinion drive with mineral spirits and a brush.
Note: If the commutator is dirty, the commutator may be cleaned with Number 00 sandpaper. Do not use emery cloth.
- Inspect all parts for wear and damage.
Caterpillar Information System:
G3304 and G3306 Engines Measuring Inlet Manifold Pressure
3034 Marine Engine Auxiliary Water Pump - Disassemble
3034 Marine Engine Auxiliary Water Pump - Install
3034 Marine Engine Auxiliary Water Pump - Remove
G3304 and G3306 Engines Measuring Inlet Manifold Temperature
37-MT, 41-MT, and 42-MT Series Starting Motors Starting Motor - Assemble - 37-MT and 41-MT
G3304 and G3306 Engines Restriction of Air Inlet and Exhaust
3034 Marine Engine Marine Transmission Oil Cooler Core - Remove and Install
3034 Marine Engine Engine Oil Cooler - Install
3034 Marine Engine Engine Oil Cooler - Remove
3500B and 3500 Marine Propulsion Engines with EUI Option Centrifugal Oil Filter - Inspect
3034 Marine Engine Inlet Manifold - Remove
G3500 Engines Air Inlet and Exhaust System Components
3034 Marine Engine Auxiliary Water Pump - Assemble
3034 Marine Engine Crankcase Breather - Remove and Install
37-MT, 41-MT, and 42-MT Series Starting Motors Starting Motor - Assemble - 42-MT
G3500 Engines Aftercooler
3034 Marine Engine Valve Mechanism Cover - Remove and Install
3034 Marine Engine - Installation Guide Engine Electrical System
HDB Series and M1 Series Heavy Duty Brushless Alternators Alternator
3034 Marine Engine Electric Starting Motor - Remove and Install
G3500 Engines Exhaust Manifold
G3500 Engines Turbocharger
3034 Marine Engine Alternator - Remove and Install