Solenoid Valve (Auxiliary Circuit) - Remove and Install - Tool Relief
Removal Procedure
Start By:
- Release the hydraulic system pressure.
Show/hide table
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. |
- Disconnect hose assembly (2) and harness assembly (3) from solenoid valve (5) .
Show/hide table
Illustration 1 | g02456496 |
- Disconnect bracket (1) and reposition.
- Remove bolts (4) and solenoid valve assembly (5) .
- Remove solenoid valve (6) .
Show/hide table
Illustration 2 | g02456604 |
- Remove O-ring seal (7), backup ring (8), and O-ring seal (9) from solenoid valve (6) .
- Remove bolts (11) and plate (10) .
Installation Procedure
- Install solenoid valve (5) in reverse order of removal.
- Tighten solenoid valve (6) to a torque of 180 ± 10 N·m (138 ± 7.4 lb ft).
Caterpillar Information System:
Wheeled Excavators Monitoring System Diagnostic Menu
422F, 428F, 432F, 434F and 444F Backhoe Loaders Battery Disconnect
Caterpillar Recommends an Inspection of the Timing Chain Tensioner on Certain Mini Hydraulic Excavators Every 1000 Hours {1241} Caterpillar Recommends an Inspection of the Timing Chain Tensioner on Certain Mini Hydraulic Excavators Every 1000 Hours {1241}
C7.1 Engines For Caterpillar Built Machines Diesel Particulate Filter Collects Excessive Soot
300.9D and 300.9D VPS Mini Hydraulic Excavator Fuses - Replace
300.9D and 300.9D VPS Mini Hydraulic Excavator Engine Air Filter Service Indicator - Inspect
300.9D and 300.9D VPS Mini Hydraulic Excavator Engine Oil Sample - Obtain
300.9D and 300.9D VPS Mini Hydraulic Excavator Stopping the Engine
300.9D and 300.9D VPS Mini Hydraulic Excavator Lubricant Viscosities
300.9D and 300.9D VPS Mini Hydraulic Excavator Radiator Core - Clean
300.9D and 300.9D VPS Mini Hydraulic Excavator Seat Belt - Inspect
Wheeled Excavators Monitoring System ECM Summary Menu
2011/05/03 New Improved Engine Software Is Now Available for Certain 315D Hydraulic Excavators {1901, 1920}
2011/03/29 A New Hose Clamp Is Now used on Certain Machine Engines {1361, 1380, 7553}
C7.1 Engines For Caterpillar Built Machines Diesel Particulate Filter Temperature Is Low
Air Conditioning and Heating R134a for All Caterpillar Machines Refrigerant Compressor
Wheeled Excavators Monitoring System Status Menu
300.9D and 300.9D VPS Mini Hydraulic Excavator Swing Bearing - Lubricate
312F and 313F Excavators Fuel Lift Pump Strainer - Replace
312E Excavator Lifting Capacities
Installation Procedure for the 371-7080 Thumb Gp {0679, 6547} Installation Procedure for the 371-7080 Thumb Gp {0679, 6547}
300.9D VPS Mini Hydraulic Excavator Machine Systems Swivel
730 EJ Articulated Truck Ejector Blade Alignment - Check/Adjust
300.9D VPS Mini Hydraulic Excavator Machine Systems Engine Design