Inlet and Exhaust Valve Seals - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 5P-1720     | 油封钩     | 1     |
开始:
- 拆下进气门和排气门。 请参阅拆解和组装, "进气与排气阀 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 利用工具 (A) 将气门杆密封 (1) 从进气和排气门导管上拆下。
图 1 显示了气门导管 (2) 从缸盖 (4) 上拆下时,气门杆密封的拆卸方式。
图 2 显示了气门导管 (2) 安装在缸盖 (4) 内时,气门杆密封的拆卸方式。
Show/hide table
图 1 | g00610601 |
Show/hide table
图 2 | g00610605 |
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 5P-1720     | 油封钩     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 不要在气门密封与气门导管接触的配合面上涂抹任何机油或密封胶。 气门密封安装完成时,在气门杆表面涂抹干净的机油,以确保密封唇的初始润滑。
- 将新气门杆密封放置就位到气门导管上。
Show/hide table
图 3 | g00610601 |
Show/hide table
图 4 | g00610605 |
- 利用工具 (A) 协助安装新气门杆密封。
图 3 显示了气门导管 (2) 从缸盖 (4) 上拆下时,气门杆密封的安装方式。
图 4 显示了气门导管 (2) 安装在缸盖 (4) 内时,气门杆密封的安装方式。
注: 气门杆密封安装在气门导管上后,确保密封正确装在气门导管的环槽内。
End By: 安装进气门和排气门。 请参阅 拆解和组装, "进气与排气阀 - 拆卸和安装"。
Caterpillar Information System:
307B Excavator Heating and Air Conditioning Control - If Equipped
3126B Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
3126B Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
307B Excavator Cab Door
307B Excavator Window (Front)
307B Excavator Drink Holder
3064 and 3066 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
307B Excavator Ashtray
307B Excavator Lighter
3114, 3116, and 3126 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
307B Excavator Light Switches
W330B Material Handler Safety Messages
3126B Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
307B Excavator Engine Speed Control
3064 and 3066 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
307B Excavator Blade Control
C-9 Engines for Caterpillar Built Machines Water Temperature Regulator
W330B Material Handler Leaving the Machine
Flash Procedure For The Software Update Of The EMCP II+ With Generator Set Control+{4490} Flash Procedure For The Software Update Of The EMCP II+ With Generator Set Control+{4490}
5230 Excavator Hydraulic System Power Shift Pressure - Check
5230B Excavator Hydraulic System Caterpillar Underspeed System - Calibrate
3064 and 3066 Engines for Caterpillar Built Machines Fuel Injection Nozzles - Remove
318B and 318B LN Excavator Lifting Capacities - 318C L with VA Boom