Crankshaft Rear Seal - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 9U-6205     | Rear Seal Installer     | 1     |
1P-0510 | Driver Group     | 1     | |
B     | FT-2806     | Alignment Tool     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Engines with 14 Bolt Housing Assembly
- Inspect the condition of the gasket. Replace the gasket, if necessary.
- Clean the areas of the parts that will contact each other.
- Use Tool (A) and a suitable press to install the crankshaft rear seal into the housing. Make sure that you install the seal to the correct depth in the housing. Refer to Specifications, "Crankshaft Seals" for additional information.
Show/hide table
Illustration 1 | g00541839 |
- Lubricate the crankshaft flange and the lip of the crankshaft rear seal with clean engine oil.
- Install Tool (A) onto the crankshaft flange.
- Put the new gasket for the housing in position on the dowels in the cylinder block.
- Carefully place housing (3) and crankshaft rear seal (4) over Tool (A) .
Show/hide table
Illustration 2 | g00606404 |
- Position housing (3) on the dowels in the cylinder block.
- Remove Tool (A) .
- Install bolts (1) and socket head bolts (2) that fasten housing (3) to the cylinder block.
Show/hide table
Illustration 3 | g00606340 |
The flywheel housing has been removed for photographic purposes only. |
- Tighten all of the bolts to a torque of 22 N·m (16 lb ft).
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
- Ensure that all parts and surfaces of the engine block are clean and free from oil, grease, and dirt.
- Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the plastic sleeve after the housing assembly is installed.
Show/hide table
Illustration 4 | g00831176 |
Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the crankshaft flange before installation.
- Place Tool (B) over housing assembly (3). This will center the housing assembly onto the crankshaft flange.
- Install the bolts with Tool (B) in position in order to fasten housing assembly (3) to the cylinder block. Tighten bolts 1 and 2 to a torque of 22 N·m (16 lb ft).
Show/hide table
Illustration 5 | g00830867 |
- Remove Tool (B). Tighten the remaining bolts in sequence to a torque of 22 N·m (16 lb ft).
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Caterpillar Information System:
3600 Heavy Fuel Engines Engine Protection Devices - Calibrate
3054 Truck Engine Crankshaft Rear Seal - Remove
3126 Truck Engine (Military) Extended Life Coolant (ELC) Cooling System Maintenance
3054 Engine for Caterpillar Built Machines Crankshaft Front Seal - Install
3126 Truck Engine (Military) Extended Life Coolant (ELC)
3054 Engine for Caterpillar Built Machines Crankshaft Front Seal - Remove
G3408 and G3412 Engines Engine Design
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump
3412E and C30 Engines Voltmeter
3408E and 3412E Engines for Caterpillar Built Machines Injection Actuation Pressure Sensor
G3606 and G3608 Engines Exhaust Manifold - Remove and Install
3054 Truck Engine Crankshaft - Install - 3054 and 3054B Engines
3612 and 3616 Fast Vessel Engines Warranty Information
3054 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
G3606 and G3608 Engines Aftercooler - Disassemble
G3606 and G3608 Engines Aftercooler - Assemble
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System Glossary of Terms
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System Initial Troubleshooting Procedure
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System System Schematic
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B and 3516C Engines Caterpillar Monitoring System System Self Test
3412E, C30 and C32 Marine Engines Turbocharger - Install
G3408 and G3412 Engines Exhaust Manifold
3408E and 3412E Engines for Caterpillar Built Machines Hydraulic Pump Drive
3054 Truck Engine Exhaust Manifold - Remove and Install