Camshaft Bearings - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 129-6671     | 反作用套筒     | 1     |
129-6672 | 拉拔器板     | 1     | |
129-6673 | 轴承安装引导器     | 1     | |
129-6674 | 备用板     | 1     | |
6F-7032 | 螺栓     | 1     | |
1P-5542 | 锥形锁紧螺柱     | 1     |
开始:
- 拆除滤清器组件。 请参阅拆解和组装, "挺杆总成 - 拆卸和安装"。
- 拆下凸轮轴。 请参考拆解和组装, "凸轮轴 - 拆卸"。
注: 上面列出的所有工具均用于 8S-2241 凸轮轴轴承工具总成 。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 安装工具 (A) 。 在螺纹上涂抹防咬合剂。
Show/hide table
图 1 | g00516210 |
Show/hide table
图 2 | g00516211 |
- 拆卸凸轮轴轴承 (1) 。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 129-6671     | 反作用套筒     | 1     |
129-6672 | 拉拔器板     | 1     | |
129-6673 | 轴承安装引导器     | 1     | |
129-6674 | 备用板     | 1     | |
6F-7032 | 螺栓     | 1     | |
1P-5542 | 锥形锁紧螺柱     | 1     |
注: 上面列出的所有工具均用于 8S-2241 凸轮轴轴承工具总成 。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将新轴承 (2) 定位在工具 (A) 中,并从发动机后面向前面安装轴承。
Show/hide table
图 3 | g00516213 |
Show/hide table
注意 |
---|
凸轮轴轴承润滑孔的位置非常重要。 定位全部七个凸轮轴轴承的挤压对接接头。 编号 1凸轮轴承油孔位于与上止点逆时针成 115 度之处,以便对齐缸体中的供油道。 将油孔与上止点顺时针成 45 度来安装2 号至 7 号凸轮轴轴承。 所有项均从发动机前端观察。 凸轮轴轴承 1、2、3、4、5 和 6 的宽度相同。 7 号凸轮轴轴承的宽度更小。 关于更多信息,请参阅技术规格手册 。 |
End By:
- 安装凸轮轴。 请参阅 拆解和组装, "凸轮轴 - 安装"。
- 安装挺杆组件。 拆解和组装, "挺杆总成 - 拆卸和安装"。
Caterpillar Information System:
3612 and 3616 Engines Compression Release Valve
3116 and 3126 Marine Engines Reference Material
G3300 Engines Engine Crankcase Breather - Clean
3116 and 3126 Marine Engines Refill Capacities
3612 and 3616 Engines Manual Valve Group (Cylinder Pressure)
3406E On-Highway Engine Engine Oil Pan - Remove and Install
3406E On-Highway Engine Gear Group (Front) - Remove
3176C and 3196 Engines For Caterpillar Built Machines Inlet Manifold - Install
3176C and 3196 Engines For Caterpillar Built Machines Inlet Manifold - Remove
3176C and 3196 Engines For Caterpillar Built Machines Water Outlet Manifold - Install
3176C and 3196 Engines For Caterpillar Built Machines Water Outlet Manifold - Remove
3406E and 3456 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
3406E On-Highway Engine Inlet and Exhaust Valve Seals - Remove and Install
G3300 Engines Ignition System Timing - Check/Adjust
3406E Truck Engine Vibration Damper
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Pan - Remove and Install
G3300 Engines Valve Data Sheet
3176C and 3196 Engines For Caterpillar Built Machines Cylinder Liner - Install
3176C and 3196 Engines For Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Remove
3406E On-Highway Engine Flywheel Housing - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Pistons and Connecting Rods - Install
3406E On-Highway Engine Engine Oil Pump - Install
C15 and C18 Petroleum Generator Sets Engine Oil Level - Check