Cylinder Head - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Loctite Graphite 50 Anti-Seize | - |
B | 8T-2998 | Lubricant | 1 |
C | 9S-3263 | Thread Lock Compound | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Thoroughly clean the spacer plate and the bottom surface of the cylinder head. A new spacer plate gasket must be installed when the cylinder head is removed.
- Apply a thin film of clean engine oil to O-ring seal (26). Install O-ring seal (26).
Show/hide table
Illustration 2 g00632048 - Install a new spacer plate gasket (25).
- Install the spacer plate on the engine.
Show/hide table
Illustration 3 g00632047 - Apply a thin film of clean engine oil to O-ring seal (22). Install O-ring seal (22).
- Install water seals (23) dry.
- Install seal (24) in the spacer plate.
Show/hide table
Illustration 4 g00580833 - Install a new cylinder head gasket (21).
Show/hide table
Illustration 5 g00580812 - Attach a suitable lifting device to cylinder head (8). Carefully position cylinder head (8) on the spacer plate. The weight of the cylinder head is approximately
235 kg (518 lb) .Show/hide tableIllustration 6 g00513934 Note: The bolts that are Marked “X” are
216 mm (8.5 inch) long. The remainders of the bolts are194 mm (7.6 inch) in length. - Apply a small amount of Tooling (A) to the bolt threads and both sides of the washers. Install the cylinder head bolts. Tighten the cylinder head bolts, as follows.
- In a numerical sequence, tighten bolts 1 through 26 to a torque of
270 ± 15 N·m (200 ± 11 lb ft) . - In a numerical sequence, tighten bolts 1 through 26 to a torque of
450 ± 15 N·m (330 ± 11 lb ft) . - In a numerical sequence, again tighten bolts 1 through 26 to a torque of
450 ± 15 N·m (330 ± 11 lb ft) .
Show/hide tableIllustration 7 g00580810 - In a numerical sequence, tighten bolts 1 through 26 to a torque of
- Install spacers (17) and bolts (18) that fasten bracket (19) to the cylinder head.
Show/hide table
Illustration 8 g00580808 - Connect the harness assembly to sensor (14), sensor (15), and ground stud (16).
- Install the bolt and support clip (13) for the harness assembly.
Show/hide table
Illustration 9 g00580807 - Install hose assemblies (10). Install the bolt and clamp (9).
Note: If the engine is not equipped with an air compressor, skip Step 14.
- Connect hose assemblies (11) and hose assemblies (12) to the air compressor.
Show/hide table
Illustration 10 g00580805 - Connect hose assembly (7) to cylinder head (8).
Show/hide table
Illustration 11 g00576240 Show/hide tableIllustration 12 g00576839 - Install O-ring seals (5) and (6) in seal assembly (3). Lubricate seal (6) with Tooling (B).
- Assemble thrust plate (1) and seal assembly (3). Apply Tooling (C) to bolts (2). Hold the assembly in position and install bolts (2). Evenly tighten bolts (2) until seal assembly (3) and O-ring seal (5) are seated against the cylinder head.
Note: Be careful to ensure that O-ring seal (5) stays in the groove in seal assembly (3).
- Install adapter (4). Ensure that the dowel in adapter (4) engages the hole in the camshaft.
Show/hide table
Illustration 1 | g00632049 |
End By:
- Install the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install".
- Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
- Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base - Remove and Install".
- Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install".
- Install the water temperature regulator. Refer to Disassembly and Assembly, "Water Temperature Regulator - Remove and Install".
Caterpillar Information System:
G3300 Engines Starting the Engine
3176C and 3196 Engines For Caterpillar Built Machines Flywheel - Remove
G3300 Engines Before Starting Engine
3406C Engines for Caterpillar Built Machines Service Meter
3176C and 3196 Engines For Caterpillar Built Machines Water Temperature Regulator - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Install
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Remove
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Cooler - Install
3406E On-Highway Engine Cylinder Head - Remove
3406C (PEEC III) Truck Engine Alternator
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Cooler - Remove
3406E On-Highway Engine Turbocharger - Disassemble
3176C and 3196 Industrial Engines Flywheel - Install
3612 and 3616 Engines Fuel Injector - Heavy Fuel Oil
3176C and 3196 Engines For Caterpillar Built Machines Flywheel Housing - Remove and Install
3406E On-Highway Engine Vibration Damper and Pulley - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valve Guides - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valves - Remove and Install
C-18 Truck Engines Compression Brake - Inspect/Adjust
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Remove
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Install
3116 and 3126 Marine Engines Engine Oil Level Gauge - Calibrate
G3300 Engines Actuator Control Linkage - Lubricate
3406E, C-10 and C-12 Truck Engines Compression Brake - Inspect/Adjust