Governor Type
The options on the DDT for the Customer Specified Parameters (CSP) can be used for the adjustment of the Governor Setting, the Governor Droop Setting and the High Idle Setting.
Governor Selection Procedure
- Connect the DDT to the ESS. Display the screen number 32 on the DDT. "GOVERNOR" will be displayed on the top line of the DDT screen number 32 .
- Press "ALT1" in order to toggle between "ISOCHRONOUS" and "DROOP" modes.
- Press "ENTER" in order to program the ESS with the desired mode.
Governor Droop Setting Procedure
- Connect the DDT to the ESS. Display the screen number 31 on the DDT. "DROOP SETTING" will be displayed on the top line of the DDT screen number 31 .
- Press the "ALT1" key.
- Enter the desired percent of the governor droop.
- Press the "ENTER" key in order to program the ESS with the desired governor droop.
High Idle Setting Procedure
- Connect the DDT to the ESS. Display the screen number 30 on the DDT. "ENG HIGH IDLE" will be displayed on the top line of the DDT screen number 30 .
- Press the "ALT1" key.
Note: The initial setting of the high idle that will be displayed on the DDT screen number 30 will be equivalent to the upper rpm setting that is programmed into the Personality Module.
- Enter the desired high idle speed in rpm.
- Press the "ENTER" key in order to program the ESS with the desired high idle speed.
Use the following procedure in order to adjust the fuel system linkage.
- Set the gas valve (7) to the closed position by pushing the stem into the valve.
Show/hide table
Illustration 1 | g00496869 |
(1) Lever. (2) Rod end. (3) Stop nuts. (4) Adapter. (5) Rod end. (6) Clevis. (7) Gas valve. |
- Rotate the actuator shaft until the actuator is in the 2 percent to 4 percent position.
- Assemble lever (1) at 40 degrees.
- Assemble the adapter (4) against the rod end (5) . Adjust the male rod end (2) to 103.7 ± 1.0 mm (4.08 ± .04 inch). Attach the lever to the male rod end and attach the clevis to the female rod end.
- Rotate clevis (6) until the actuator indicator is 2.0 ± 0.5 degrees from the closed position.
- Tighten the stop nuts (3) against the adapters.
Caterpillar Information System:
3054 Engine Rocker Shaft
3406E Truck Engines Electrical System
G3606 and G3608 Engines Driven Equipment - Check
3406E and 3456 Engines for Caterpillar Built Machines Compression Brake
3508, 3512 and 3516 Engines Crankshaft Position for Unit Injector Adjustment and Valve Lash Setting
3406E Truck Engines Cooling System
3508, 3512 and 3516 Engines Engine Design
3508, 3512 and 3516 Engines Engine Design
3508, 3512 and 3516 Engines Engine Design
3306B Industrial Engine Fuel Transfer Pump
Instruction For Increasing The Horsepower Rating On The 3406B Truck Engines And The 3406C Truck Engines{1901} Instruction For Increasing The Horsepower Rating On The 3406B Truck Engines And The 3406C Truck Engines{1901}
G3612 and G3616 Engines Overhaul (Major)
G3612 and G3616 Engines Pressure Module Calibration
3054 Engine Fuel Transfer Pump
G3612 and G3616 Engines Oil Pressure Sensor Calibration
3054 Engine Fan Drive
3512 Industrial Engine Coolant Recommendations
3054 Engine Engine Oil Filter Base
G3500 Engines Model View Illustrations
3054 Engine Muffler
G3500 Engines Product Description
G3612 and G3616 Engines Wastegate Actuator Adjustment
3406E Generator Set Engines Generator Identification
3406C (PEEC III) Truck Engines Brakesaver Troubleshooting