The Machine button allows the operator to adjust the machine’s operation settings.
Illustration 1 | g03887722 |
(1) Machine Button |
To access the Machine menus and adjust settings, press the "Machine" button (1).
Machine > Settings
- Press the Machine button (1) located on the right side of the Display. The Machine menu page will appear.
Show/hide table
Illustration 2 g06095463 (2) "Settings" menu button
(3) BACK Button
(4) HOME Button - Press the "Settings" menu button (2) to enter the "Settings" menu page.
- Press the BACK button (3) to return to the previous menu.
- Press the HOME button (4) to return to the HOME page.
Note: Settings menu pages will vary, depending on the machine model and equipped features.
Illustration 3 | g06095469 |
(5) Settings menu button group
(6) Non-Interactive Scroll Bar with Menu Sliding Indicator (7) UP button (8) OK button (9) DOWN button |
Note: Some of the menu buttons in the menu button group are hidden. The Display can only show four menu buttons at a time. Use the UP Arrow button (7) or the DOWN Arrow button (9) to scroll through the list of menu buttons. The Menu Sliding Indicator of the Non-Interactive Scroll Bar (6) will move accordingly with the page.
Machine > Settings > Payload
Models 988, 990, and 994 when Cat® Production Measurement is installed and enabled.
Press the "Payload" button. The "Payload" button will highlight in yellow and the Payload menu pages will appear.
The Payload Hotkey button is available on the following models when the Cat Production Measurement (CPM) installed and enabled.
- 998 T4f Wheel Loader
- 988 LRC Wheel Loader
- 990 T4f Wheel Loader
- 990 LRC Wheel Loader
- 992 T4f Wheel Loader
- 992 LRC Wheel Loader
- 993 T4f Wheel Loader
- 993 LRC Wheel Loader
- 994 T4f Wheel Loader
- 994 LRC Wheel Loader
Illustration 4 | g06095470 |
(10) Payload menu button |
Press the Payload menu button (10). The button will highlight in blue, then in yellow. The Payload menu pages will appear.
Choose from the following selections:
- Weigh range
- Print tickets
- Tip-off
- Payload display mode
- Weigh units
- Payload Horn
- List management
Note: For more information on the Payload Control System, refer to Systems Operation/Testing and Adjusting, UENR6737, "988K and 990K Wheel Loaders Cat® Production Measurement Application".
Machine > Settings > Kickouts
Models 836 (when ABP is installed), 988, 990, and 994.
Illustration 5 | g06095474 |
(11) "Kickouts" menu button |
- Press the Kickouts menu button (11). The button will turn blue, then yellow. The Kickouts menu page will appear.
- Choose from the following selections:
- Raise Kickout
- Lower Kickout
- Rackback Kickout
- Dump Kickout
Show/hide tableIllustration 6 g06095477 (12) Kickouts menu button group
(13) Menu buttons: Enabled and Disabled - Press the intended button in the menu button group. The button will turn blue. The intended settings page will appear.
- Press either the Enabled menu button or the Disabled menu button. The button will turn blue, then yellow. A check mark will also appear in the selected yellow button.
- Press either the "Enabled" menu button or the "Disabled" menu button. The selected button will turn yellow. A check mark will also appear in the selected button.
Machine > Settings > Ride Control
Models 988 and 990 with Ride Control System installed.
Illustration 7 | g06095482 |
(3) BACK Button
(14) Ride Control menu button (15) ENTER DATA button – Forward Activation Speed (16) ENTER DATA button – Reverse Activation Speed |
Machine > Settings > Ride Control> Forward Activation Speed
Illustration 8 | g06095483 |
(3) BACK button
(4) HOME button (8) OK button |
- Press the Ride Control menu button. The button will highlight in blue. The "Ride Control" settings page will appear.
- Press the ENTER DATA button (15) for the Forward Activation Speed. A keypad will appear.
- On the keypad, type in an intended number for the Activation Speed (Forward or Reverse). After entering the value, press the OK button (8).
- Press the BACK button (3) again to return to the previous page.
- Press the HOME button (4) to return to the HOME page.
- Press the BACK button (3) again to return to the previous menu.
Machine > Settings > Ride Control> Reverse Activation Speed
Illustration 9 | g06095487 |
(3) BACK button
(4) HOME button (8) OK button |
- Press the Ride Control menu button. The button will highlight in blue. The "Ride Control" settings page will appear.
- Press the ENTER DATA button (16) for the Reverse Activation Speed. A keypad will appear.
- On the keypad, type in an intended number for the Activation Speed (Forward or Reverse). After entering the value, press the OK button (8).
- Press the BACK button (3) again to return to the previous page.
- Press the HOME button (4) to return to the HOME page.
Machine > Settings > Rimpull
Models 988, 990, and 994.
Illustration 10 | g06095496 |
(17) "Rimpull" menu button
(18) Increment/Decrement bar |
- Press the Rimpull menu button (17). The button will highlight in blue, then yellow. The Set Rimpull Control settings page will appear.
The Set Rimpull Control page has three settings:
- Medium High (percentage)
- Medium Low (percentage)
- Low (percentage)
- To decrease or increase each percentage, press either the MINUS (-) button or the PLUS (+) button on the Increment/Decrement bar (18).
- When an intended number appears, press the OK button (8) to set. The newly set number will appear in white text.
- Press the BACK button (3) to return to the previous menu.
- Press the HOME button (4) to return to the HOME page.
Controlled Throttle Shifting (CTS)
Machine > Settings > Controlled Throttle Shifting (CTS)
Illustration 11 | g06095498 |
(19) "Controlled Throttle Shifting" menu button |
- Press the Controlled Throttle Shifting button (19). The button will turn blue, then yellow. The Controlled Throttle Shifting (CTS) menu page will appear.
- Press either the Enabled button or the Disabled button. The selected button will highlight in blue, then yellow. A black check mark will then appear in the selected yellow menu button.
- Press the BACK button (3) to return to the previous menu.
- Press the HOME button (4) to return to the HOME page.
Machine > Settings > Autolube
Models 988 and 990 with Autolube installed.
Model 994.
Illustration 12 | g06095502 |
(6) Non-Interactive Scroll Bar with a Menu Sliding Indicator
(7) UP Arrow button (9) DOWN Arrow button (20) "Autolube" menu button (21) ENTER DATA button |
- Press the UP Arrow button (7) or DOWN Arrow button (9) to scroll the Settings menu to the Autolube menu button (20). The Menu Sliding Indicator on the Non-Interactive Scroll Bar will move accordingly with the page.
- Press the Autolube menu button (20). The button will highlight in blue, then yellow. The Autolube page will appear.
- Press the ENTER DATA button (21) found in the Pressure settings box on the Autolube page. A keypad will appear.
Show/hide table
Illustration 13 g06095511 (3) BACK button
(4) HOME button
(8) OK button
(22) BACKSPACE button - On the keypad, type in an intended number for the Autolube Minimum Pressure. To make a correction, press the BACKSPACE button (22) to backspace over the number.
- When an intended number appears, press the OK button (8) to set.
- Press the BACK button (3) to return to the previous menu.
- Press the HOME button (4) to return to the HOME page.
Machine > Settings > Auto Idle
Illustration 14 | g06095517 |
(23) "Auto Idle" menu button |
- Press the Auto Idle button (23). The button will highlight in blue, then yellow. The Auto Idle settings page will appear.
Machine > Settings > Auto Idle > Auto Idle Enable
Illustration 15 | g06095520 |
(24) "Auto Idle Enable" menu button |
- Press the Auto Idle Enable button (24). The button will highlight in blue, then yellow. The Auto Idle Enable settings page will appear.
- Press either the Enabled or Disabled button. The selected button will highlight in blue, then yellow. A black check mark will then appear in the selected yellow menu button.
- Press the OK button (8) to set.
- Press the BACK button (3) to return to the previous menu.
- Press the HOME button (4) to return to the HOME page.
Machine > Settings > Auto Idle > Auto Idle Delay Time
Illustration 16 | g06095527 |
(25) "Auto Idle Delay Time" menu button |
- Press the Auto Idle button. The Auto Idle menu page will appear.
- Press the Auto Idle Delay Time menu button (25). The button will turn blue, then yellow. The Auto Idle Delay Time menu page will appear.
- To select a delay time, press an intended menu button on the Auto Idle Delay Time settings screen. Choose from the following selections:
- 5 sec(onds)
- 10 sec(onds)
- 20 sec(onds)
- 40 sec(onds)
The selected button will highlight in blue, then yellow. A black check mark will then appear in the selected yellow menu button. Press the OK button (8) to set.
- Press the "OK" button (9) to set.
- Press the BACK button (3) to return to the previous menu.
- Press the HOME button (4) to return to the HOME page.
Machine > Settings > Implement Modulation
Models 824, 825, 826, 834, and 844.
Illustration 17 | g06095531 |
(26) "Implement Modulation" menu button |
- Press the Implement Modulation menu button (26). The button will highlight in blue, then in yellow. The Implement Modulation menu page will appear.
- Select and press the intended menu button on the Implement Modulation menu page. Choose from the following selections:
- Standard
- Fine
- Fast
The selected button will highlight in blue, then yellow. A black check mark will then appear in the selected yellow menu button. Press the OK button (8) to set.
- Press the "OK" button (9) to set.
- Press the BACK button (3) to return to the previous menu.
- Press the HOME button (4) to return to the HOME page.