Data Link - Test
Show/hide table
Illustration 1 | g03672523 |
Data link connections of models: 834K, 836K and 988 |
Show/hide table
Illustration 2 | g03672446 |
Data link connections of models: 966M, 966M XE, 972M, 972M XE, 980M and 982M 950M |
The following is a list of codes associated with the machine data link.
Show/hide table
Communication Gateway #1 ECM (VIMSTM Main) ECM
(MID 161) |
||
---|---|---|
DTC (1) | DTC Description | System Response |
296-9 | Transmission Control - Abnormal Update Rate | There is a lack of communication between VIMS and the Transmission ECM. |
590-9 | Engine Control Module - Abnormal Update Rate | There is a lack of communication between VIMS and the Engine ECM. |
596-9 | Implement Control - Abnormal Update Rate | There is a lack of communication between VIMS and the Implement ECM. |
890-9 | Telemetry Data Link - Abnormal Update Rate | There is a lack of communication between VIMS and the telemetry components. |
1250-9 | Remote Communication Module - Abnormal Update Rate | There is a lack of communication between VIMS and the remote communication components. |
2448-9 | Graphical Display Module: Abnormal Update Rate | There is a lack of communication between VIMS and the graphical display module. |
Show/hide table
(1) | DTCs are shown as CID-FMI |
Each data link circuit:
- Is an input and output of select electronic control modules (ECMs)
- Is designed to carry communications between the ECMs
- Consists of internal control circuits and the connecting harness wiring
Possible -9 DTC causes are:
- Poor ECM connections on the data link
- Incorrect ECM hardware or software part numbers
- Failed data link harness
- Failed ECM on the data link
- Failed component on the data link
Show/hide table
Troubleshooting Steps | Values | Results |
---|---|---|
1. Check for Diagnostic Codes A. Connect Cat® Electronic Technician (Cat ET) to the machine. B. Check for active DTCs. |
There are no active data link associated codes |
OK - There are no active data link associated DTCs. STOP Not OK - There are active data link associated DTCs. Go to Step 2. |
2. Check Connectors A. Inspect the circuit harness connectors. |
Connectors are: * Clean * Secure * In good condition |
OK - Connectors are OK. Go to Step 3. Not OK - Connectors are not OK. Repair: A. Correct any connection problem. B. Verify that the problem is corrected. STOP |
3. Check the Hardware Part Numbers and the Software Versions A. On Cat ET, click "ECM Summary". B. Check "Software Group" for info(1). |
*Hardware is the correct part number *Software is the latest version |
OK - The hardware and software are correct. Go to Step 4. NOT OK - The hardware or software are not correct. Repair: A. Install correct part number ECMs, if necessary(2). B. Update the software(3). C. Clear the DTC. STOP |
4. Check For Short to Ground A. Turn off the disconnect switch. B. Disconnect all DTC associated ECMs and components from the data link. C. At the harness connector for the Communication Gateway # 1 ECM, measure the resistance between frame ground and the following harness contacts: * +Data Link * -Data Link |
≥5000Ω |
OK - The resistance is correct. Go to Step 5. NOT OK - The resistance is not correct. There is a short between frame ground and the data link circuit in the harness. Repair: Repair or replace the harness. Go to Step 7. |
5. Check For Short to +Battery The disconnect switch remains off. All DTC associated ECMs and components remain disconnected from the harness. A. At the harness connector for the DTC associated ECMs and components, measure the resistance between the following harness contacts: * +Battery and +Data Link * +Battery and -Data Link |
≥5000Ω |
OK - The resistance is correct. Go to Step 6. NOT OK - The resistance is not correct. There is a short between the +battery and the data link circuit in the harness. Repair: Repair or replace the harness. Go to Step 7. |
6. Check For an Open The disconnect switch remains off. All DTC associated ECMs and components remain disconnected from the harness. A. Measure the resistance between the following harness contacts: * Communication Gateway ECM # 1 +Data Link and the DTC associated ECMs and components +Data Link * Communication Gateway ECM # 1 -Data Link and the DTC associated ECMs and components -Data Link |
<5Ω |
OK - The resistance is correct. The ECM or component may have failed. Repair: A. Component Failure: Replace the component. Go to Step 7. B. ECM Failure: Contact your Technical Communicator (TC)(2). NOT OK - The resistance is not correct. There is an open in the harness. Repair: Repair or replace the harness. Go to Step 7. |
7. Recheck the DTC A. Reconnect all of the DTC associated ECMs and components. B. Turn on the disconnect switch and the key start switch. C. Using Cat ET, check the DTC. |
DTC is not active |
OK - DTC is not active. STOP NOT OK - DTC is active. Repair: Perform this procedure again. If the problem is not found, contact your TC. STOP |
Show/hide table
(1) | Consult the Business Unit that produces the product for the correct part numbers. |
(2) | See Testing and Adjusting, "Electronic Control Module (ECM) - Replace". |
(3) | See Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program". |
Caterpillar Information System:
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Piston Pump (Brake Charging)
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Hydraulic Tank - Remove and Install
794 AC Off-Highway Truck Alternate Exit
2014/04/23 New Software Patch Is Now Available for Cat® MineStar Health Office v3.1 {7605}
794 AC Off-Highway Truck Stairway (Powered) Operation
AP1055F Asphalt Paver Machine Systems Pressure Reducing Valve - Test and Adjust - Shift Solenoid
794 AC Off-Highway Truck Specifications
785G Off-Highway Truck/Tractor Electrical and Hydraulic Systems Diagnostic Trouble Codes
AP1055F Asphalt Paver Machine Systems Pump Control Valve (Auxiliary) - Test and Adjust
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems General Information (Brake System)
980M and 982M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Position Sensor (Tilt Linkage) - Replace
2014/04/18 A New Check Valve Is Now Used on Certain 793D Off-Highway Trucks {1374, 5057, 5067, 5068}
Landfill Compactors, Soil Compactors, Wheel Dozers, and Wheel Loaders VIMSTM 3G Data Link Configuration Status - Test
R2900G Load Haul Dump Hydraulic System Relief Valve (Line) - Test and Adjust
424B Backhoe Loader Machine Systems Bucket Positioner Control - Remove and Install
424B Backhoe Loader Machine Systems Tilt Cylinder - Remove and Install
Rework Procedure to Update AP800D Asphalt Pavers with 25KW Generator Group {4450} Rework Procedure to Update AP800D Asphalt Pavers with 25KW Generator Group {4450}
980M Tier 3, 982M Tier 3 and 980L Tier 3 Wheel Loader Power Train Transmission to Output Transfer Gears - Connect
980M Tier 3, 982M Tier 3 and 980L Tier 3 Wheel Loader Power Train Torque Converter to Transmission, Output Transfer Gears - Connect
C13 Engine for Caterpillar Built Machines Pressure Sensor (NRS Differential) - Remove and Install
AP1055F Asphalt Paver Machine Systems Fan Speed (Ventilation) - Test
794 AC Off-Highway Truck Systems Control Manifold (Brake)
794 AC Off-Highway Truck Systems Foot Brake Control
794 AC Off-Highway Truck Systems Service and Parking Brake