Main Relief Valve - Test and Adjust
技术规格
Show/hide table
834K 主安全阀测试     | |||
项目     | 技术规格     | 实际值     | 发动机转速     |
主安全阀压力     | 31025 ± 500 kPa (4500 ± 72 psi)( 38 L/min (10 US gpm) 下)     |
    | 断开     |
锁紧螺母(扭矩)     | 50 ± 7 N·m (37 ± 5 lb ft)     |
    |     |
主安全阀(扭矩)     | 65 ± 5 N·m (48 ± 4 lb ft)     |
    |     |
Show/hide table
836K 主安全阀测试     | |||
项目     | 技术规格     | 实际值     | 发动机转速     |
主安全阀压力     | 27600 ± 500 kPa (4000 ± 72 psi)( 38 L/min10 ( US gpm) 下)     |
    | 断开     |
锁紧螺母(扭矩)     | 50 ± 7 N·m (37 ± 5 lb ft)     |
    |     |
主安全阀(扭矩)     | 65 ± 5 N·m (48 ± 4 lb ft)     |
    |     |
Show/hide table
图 1 | g02776116 |
机具主安全阀 (1) 安全阀 (2) 锁紧螺母 (3) 调整螺栓 |
Show/hide table
扭矩规格     | |
图中编号     | 扭矩     |
锁紧螺母 (2)     | 50 ± 7 N·m (37 ± 5 lb ft)     |
主安全阀 (1)     | 65 ± 5 N·m (48 ± 4 lb ft)     |
简介
液压系统的主安全阀位于主控制阀的进气歧管中。 主安全阀不能在机器上调整。
以下步骤可确定主安全阀是否需要调整。
所需工具
Show/hide table
所需工具     | |||
工具     | 零件号     | 说明     | 数量     |
A     | 1U-9358     | 测试歧管组     | 1     |
测试步骤
- 将主安全阀 (1) 从进气歧管 (2) 上拆下。
Show/hide table
图 2 | g03396670 |
机具主安全阀的位置 (1) 主安全阀 (2) 进气歧管 |
注: 主安全阀 (1) 位于机具阀内侧方的进气歧管 (2) 中。
- 将主安全阀 (1) 安装到 1U-9358 测试歧管组 工具 (A) 中,以便在测试台架上测试安全阀。 拧紧安全阀至扭矩为 65 ± 5 N·m (50 ± 4 lb ft)。
注: 机具主安全阀 (1) 的设定值高于泵切断压力。 机具主安全阀必须以 38 L/min (10 US gpm) 的流量测试。 有关正确的压力设定值,请参阅技术规格部分。
调整步骤
Show/hide table
图 3 | g02776116 |
机具主安全阀 (1) 安全阀 (2) 锁紧螺母 (3) 调整螺栓 |
- 松开锁紧螺母 (2) 的同时将调整螺钉 (3) 保持到位。
- 顺时针转动调整螺栓 (3) 以增大压力设定值,逆时针转动调整螺栓 (3) 以减小压力设定值。
- 设定压力后,拧紧锁紧螺母 (2) 的同时将调整螺栓 (3) 拧紧到扭矩为 50 ± 7 N·m (37 ± 5 lb ft)。
- 将主安全阀 (1) 安装回进气歧管中。 拧紧主安全阀至扭矩为 65 ± 5 N·m (48 ± 4 lb ft)。
Caterpillar Information System:
Procedure to Install the Groeneveld Auto Lubrication System on Certain 777G Off-Highway Trucks{1408, 7510, 7513, 7516, 7540} Procedure to Install the Groeneveld Auto Lubrication System on Certain 777G Off-Highway Trucks{1408, 7510, 7513, 7516, 7540}
Installation of the 388-8284 Camera Kit (Back-Up) {1435, 7450, 7490} Installation of the 388-8284 Camera Kit (Back-Up) {1435, 7450, 7490}
Cat MT4400D AC Off-Highway Truck VIMSTM 3G and Truck Payload Measurement System (TPMS) Display Modules
Installing the 388-8283 Radio Installation Gp (Radio Ready) {7268, 7329, 7338, 7338} Installing the 388-8283 Radio Installation Gp (Radio Ready) {7268, 7329, 7338, 7338}
834K Wheel Dozer and 836K Landfill Compactor Machine Systems Lift and Tilt Cylinder Drift - Check
D-Series and D2-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Bogie and Idler - Inspect/Replace
SS-56 Felling Head Hydraulic Cylinder (Accumulator Arm) - Remove and Install
Installation Procedure for the 388-8276 Cab Door and Mounting Kit (GLASS) on All D Series Skid Steer Loaders, Multi Terrain Loaders, and Compact Track Loaders {7308} Installation Procedure for the 388-8276 Cab Door and Mounting Kit (GLASS) on All D Series Skid Steer Loaders, Multi Terrain Loaders, and Compact Track Loaders {7308}
259D, 279D and 289D Compact Track Loaders, 257D, 277D and 287D Multi Terrain Loaders and 236D, 242D, 246D and 262D Skid Steer Loaders Engine Supplement Radiator and Hydraulic Oil Cooler - Remove and Install
Installing the 388-8275 Cab Side Window Kit {7310} Installing the 388-8275 Cab Side Window Kit {7310}
2014/03/04 A New Special Instruction Is Available to Install 442-4755 Fuel Tank and Mounting Gp on Certain Vibratory Soil Compactors {1273}
2013/10/21 New Slack Adjuster Group is Used on the 777G Off-Highway Trucks {4257, 4261}
2014/07/18 Procedures to Update or Install the Lincoln or Groeneveld Auto Lubrication Systems on Certain 777G Off-Highway Trucks are Now Available {1408, 7510, 7513, 7516, 7540}
Cat® Detect and Cat® MineStar System Onboard Configuration for the MS352 Satellite Receiver Receiver Connection
CB34B, CB34B XW, CC34B and CB36B Vibratory Utility Compactors Propel System Neutral Start Switch - Test and Adjust
988K Wheel Loader, 834K Wheel Dozer and 836K Compactor Machine Systems Main Control Valve - Disassemble
259D, 279D and 289D Compact Track Loaders, 257D, 277D and 287D Multi Terrain Loaders and 236D, 242D, 246D and 262D Skid Steer Loaders Engine Supplement Air Cleaner - Remove and Install
Cat MT4400D AC Off-Highway Truck VIMSTM 3G and Truck Payload Measurement System (TPMS) VIMSpc Software
836K Landfill Compactor and 834K Wheel Dozer Machine Systems Main Control Valve - Remove and Install
D-Series and D2-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Engine Air Filter Primary Element - Clean/Replace
D-Series and D2-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Rollover Protective Structure (ROPS) and Falling Object Protective Structure (FOPS) - Inspect
Installing the 388-8285 Engine Speed Control Pedal {1269} Installing the 388-8285 Engine Speed Control Pedal {1269}
2014/06/20 New Filter Bypass Switch Is Now Used on Certain Large Off-Highway Trucks {1435, 3067, 5068}
Installation instructions for the 390-0349 Snow Blade and Mounting Gp On Certain Motor Graders{6158, 6159} Installation instructions for the 390-0349 Snow Blade and Mounting Gp On Certain Motor Graders{6158, 6159}