Front Axle - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 9U-7546     | 底座组件     | 2     |
9U-7542 | 管组件     | 4     | |
4C-5809 | 电动液压泵总成     | 1     | |
B     | 138-7574     | 连杆支架     | 2     |
C     | 9U-7546     | 底座组件     | 1     |
D     | 180-3033     | 一套修理台     | 2     |
开始:
- 拆下转速传感器(牵引力控制)
- 拆下前挡泥板。
- 将蓄电池断路开关转到断开位置。
- 接合停车制动器。 塞住前轮胎。
- 利用工具 (A) 升起机器前部。 机器应当升起足够的高度,以便于前轮胎的拆卸。
Show/hide table
图 1 | g01185938 |
- 将工具 (C) 定位到机器中心位置的下方,用作附加支撑。
Show/hide table
图 2 | g01186780 |
- 拆下前轮和轮胎。 请参阅拆解和组装, "车轮 - 拆卸"。
- 断开前驱动轴 (1) 。
Show/hide table
图 3 | g01186280 |
- 拆下防护罩组件 (2) 。 断开管组件 (3) 。
Show/hide table
图 4 | g01186295 |
- 拆下用来固定管组件 (3) 的夹子 (4) 。 断开软管组件 (5) 和 (6) 。
Show/hide table
图 5 | g01186387 |
- 拆下螺栓 (7) 后将块 (8) 放到一边。 断开软管组件 (9) 。
Show/hide table
图 6 | g01186622 |
- 拆下螺栓 (11) 后断开稳定杆 (10) 。
Show/hide table
图 7 | g01186537 |
- 拆下顶部的三条螺栓 (12) 。
Show/hide table
图 8 | g01186560 |
- 将适当起吊设备连接至支架 (13) 。 托架 (13) 的重量约为 35 kg (75 lb)。 拆下下部螺栓 (12) 后拆下托架 (13) 。
Show/hide table
图 9 | g01186595 |
- 将工具 (B) 和适当的起吊设备固定到前桥组件 (20) 上。 前桥组件 (20) 的重量约为 1925 kg (4244 lb)。 利用适当的起吊设备撑住前桥组件 (20) 的重量。
Show/hide table
图 10 | g01186614 |
Show/hide table
图 11 | g01186765 |
- 拆下螺母 (17) 、垫圈 (15) 和销组件 (16) 。 将悬架油缸 (14) 放到一边。 对另一侧重复上述步骤。 将前悬架 (18) 落到工具 (D) 上。 拆下螺栓 (19) 后将前桥组件从机器上落下。
安装步骤
- 按与拆卸相反的顺序安装前桥组件 (20) 。
Caterpillar Information System:
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Axle Shaft - Remove and Install
C175-16 Locomotive Engine Valve Mechanism
C27 and C32 Engines for Caterpillar Built Machines Cylinder Block
2011/07/28 Correction to Disassembly and Assembly , "Final Drive and Brake - Install" for R2900G Load Haul Dump Machines {4050, 4251}
2470C, 2570C and 2670C Wheel Feller Bunchers Machine Systems Steering Cylinder - Remove and Install
2011/06/08 New Software Containing Engine Idle Shutdown Feature (EIS) Is Now Used on Certain Off-Highway Trucks {1920, 7620}
AP1000E and BG1000E Asphalt Pavers Machine Systems Relief Valve (Screed Counterbalance) - Test and Adjust
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Rear Drive Shaft - Remove and Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Pressure Reducing Valve - Test and Adjust - Shift Solenoid
AP1000E and BG1000E Asphalt Pavers Machine Systems Pump Control Valve (Auxiliary) - Test and Adjust
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Center Drive Shaft - Remove and Install
3516B Engine for 994F and 994H Wheel Loaders Speed Control (PWM) - Test
C13, C15, and C18 Tier 4 Final Engines Vibration Damper
735B, 740B and 740B EJECTOR Articulated Trucks Power Train Center Axle - Remove and Install
3516B Engine for 994F and 994H Wheel Loaders Throttle Lock - Test
541 Series 2 Track Feller Buncher and 552 Series 2 Track Feller Buncher Machine Systems Travel System
992K Wheel Loader Object Detection Sensor - Clean/Inspect
541 Series 2 Track Feller Buncher and 552 Series 2 Track Feller Buncher Machine Systems Control Valve (Travel)
2011/07/08 A New Pump Control Valve Group is Now Used on the Piston Pump Groups on Certain Off-Highway Trucks {5070}
2013/09/12 A New Aftercooler Core Assembly is Now Used in the Air Aftercooler Group on the 773F and 775F Off-Highway Trucks {1063, 1353, 1806}
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
C27 Generator Set Fuel System Primary Filter (Water Separator) Element - Replace
541 Series 2 Track Feller Buncher and 552 Series 2 Track Feller Buncher Machine Systems Leveling System
C3.4B Industrial Engine Fan Clearance - Check