Speed and Vibratory Module Group - Cab
Show/hide table
Illustration 1 | g01410036 |
(1) Torque for nut ... 17 ± 3 N·m (13 ± 2 lb ft)
Vibratory Sensor
Note: The following is a procedure for installing the vibratory sensor.
- Screw the vibratory sensor (2) until the sensor touches the tips of the teeth on the shaft.
- Unscrew approximately one turn.
- Gap between the vibratory sensor (2) and the shaft 1.5 ± 0.5 mm (0.06 ± 0.02 inch)
- Tighten the nut in order to secure the sensor.
- Install the boot on the harness before connecting wires to the magnetic sensor.
Speed Sensor
Note: The following is a procedure for installing the speed sensor.
- Run the machine without the speed sensor (3) until one of the four corners of the square nut faces the hole for the sensor.
- Apply 5P-3413 Pipe Sealant to the threads of the speed sensor (3) .
- Screw the speed sensor (3) until the sensor touches the square nut.
- Unscrew approximately one turn.
- Gap between the speed sensor (3) and the shaft 1.5 ± 0.5 mm (0.06 ± 0.02 inch)
- The nut that secures the speed sensor (3) should be torqued to 16 ± 1 N·m (140 ± 10 lb in).
Caterpillar Information System:
140H and 160H Motor Graders Maintenance Interval Schedule
R1600G Load Haul Dump Parking Brake Manual Release
R1600G Load Haul Dump Engine and Machine Warm-Up
Reuse and Salvage for Turbochargers {0760, 0767, 1052} Reuse and Salvage for Turbochargers {0760, 0767, 1052}
924H, 924HZ, 928HZ and 930H Wheel Loaders MID 081 - CID 1960 - FMI 09
140M Motor Grader Engine Supplement Fuel Priming Pump and Water Separator - Remove and Install
Bench Test Procedure For A 784B, 784C, 785B, 785C, and 785D Off-Highway Truck Torque Converter{3101} Bench Test Procedure For A 784B, 784C, 785B, 785C, and 785D Off-Highway Truck Torque Converter{3101}
Adjustment Procedure for the Extendable Stick Wear Pads{6533} Adjustment Procedure for the Extendable Stick Wear Pads{6533}
CP54 and CS54 Vibratory Soil Compactors Machine Systems Speed and Vibratory Module Group - Canopy
2007/08/27 Precautions for Cylinder Liner Installation {1201, 1216}
3176C Engine for the R1600G and the R1700G Load Haul Dumps Timing - Calibrate
797 Rear Wheel Bearing Full Single Life Reusability Guidelines {4201} 797 Rear Wheel Bearing Full Single Life Reusability Guidelines {4201}
140M Motor Grader Engine Supplement Aftercooler - Remove
14M Motor Grader Operator Controls
2007/08/27 Precautions for Cylinder Liner Installation {1201, 1216}
CP76 and CS76 Vibratory Compactors Propel System Piston Pump Neutral (Drum Propel Pump) - Adjust
14M and 16M Motor Graders Machine Systems General Information - Autolube System, If Equipped
CP54 and CS54 Vibratory Soil Compactors Machine Systems Air Cleaner
2007/09/03 A new Fuel Heater Group is Available {1296}
CP76 and CS76 Vibratory Compactors Propel System Piston Pump Neutral (Axle Propel Pump) - Adjust
3176C Engine for Caterpillar Built Machines ECM - Replace
3176C Engine for Caterpillar Built Machines Electronic Service Tool Does Not Communicate
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Pilot Oil Accumulator (Dead Engine, Lift Arm Lower) - Test and Charge
CAESultra v3.2 Software Installation{7604, 7620} CAESultra v3.2 Software Installation{7604, 7620}