- Track Feller Buncher:
- 1090 (S/N: BZJ1-206)
- 1190 (S/N: BZK1-1220,2160-2162)
- 1190T (S/N: BZL1-1321,2210-2210)
- 1290T (S/N: BZM1-207)
- 1390 (S/N: B3F1-205,206-2312)
- 511 (S/N: 5111-286)
- 521 (S/N: 5211-315)
- 522 (S/N: 5221-247)
- 532 (S/N: 5321-176)
- 541 (S/N: 5411-211)
- 551 (S/N: 5511-117)
- 552 (S/N: 5521-146)
- TK711 (S/N: 1011-276)
- TK721 (S/N: 1021-367)
- TK722 (S/N: 1031-467)
- TK732 (S/N: 1041-549)
- TK741 (S/N: 2021-233)
- TK751 (S/N: 3011-261)
- TK752 (S/N: 3021-425)
- 1190 (S/N: BZK1-1220,2160-2162)
Introduction
The lines for travel may retain residual oil pressure from a turn. This will cause a slow response to return to a straight travel. The remaining residual pressure can also cause the machine to not track straight.
Do not perform any procedure in this publication until you understand the information that is contained in this publication.
Preparation of the Machine
- Clean the machine. Cleaning the machine will help to prevent dirt from entering the hydraulic system when hydraulic components are being installed.
- Move the machine to a level area. Lower attachment to the ground.
- Release the oil pressure in all of the implement circuits (the boom, the stick and the attachment) before any of the hydraulic lines or any of the components are disconnected or removed.
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Personal injury can result from contact with hot hydraulic oil and from contact with hydraulic oil that is under high pressure. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. The hydraulic oil pressure must be released before any service on the hydraulic system is performed or serious personal injury could occur. Verify that all of the work tools have been completely lowered to the ground. Release the hydraulic oil pressure at the hydraulic tank through the breaker relief valve when the breaker relief valve is cool enough to touch with your bare hand. Verify that the hydraulic oil is cool before you begin to remove any hydraulic components or hydraulic lines. |
- Shut off the engine and turn the switch to the ON position. Put the hydraulic lockout control in the UNLOCK position.
- Cycle all control levers through the full range of motion. This will release any pressure that might be present in the hydraulic system.
Note: If the hydraulic circuit requires the activation of a switch for operation, activate the necessary switches for the hydraulic circuit.
- Turn the start switch to the OFF position.
- Move the hydraulic lockout control to the LOCKED position.
Note: When the hydraulic lockout control is in the LOCKED position no implements will function.
- Push down on the hydraulic tank breaker relief valve until all pressure is released.
- When the pressure in the hydraulic system has been released then the hydraulic oil lines and the components can be removed.
Required Parts
Required parts for the Full Tail Swing machines see Table 1.
Required Parts     | ||
---|---|---|
Qty     | Part Number     | Description     |
4     | 122-2340     | Connectors     |
4     | 3J-1907     | O-Ring Seals     |
4     | 6V-8397     | O-Ring Seals     |
4     | 279-5058     | Manifold     |
2     | 303-5984     | Tube As     |
4     | 1P-3703     | Rectangular Seals     |
16     | 8C-8729     | Bolts     |
16     | 8T-4223     | Hard Washers     |
Required parts for the Zero Tail Swing machines see Table 2.
Required Parts     | ||
Qty     | Part Number     | Description     |
4     | 122-2340     | Connectors     |
4     | 3J-1907     | O-Ring Seals     |
4     | 6V-8397     | O-Ring Seals     |
4     | 279-5058     | Manifold     |
2     | 303-5984     | Tube As     |
4     | 1P-3703     | Rectangular Seals     |
16     | 8T-4223     | Hard Washers     |
16     | 8T-6868     | Bolt     |
Rework Procedure
Illustration 1 | g01408081 |
(1) Connector (2) O-Ring Seal (3) O-Ring Seal (4) Manifold (5) Tube Assembly (6) Rectangular Seal (7) Hard Washer (8) Bolts |
Install parts that are shown in Illustration 1.
Illustration 2 | g01408100 |
See illustration 2 for a view of installed parts on the machine.