Removal Procedure
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1U-9200     | Lever Puller Hoist     | 1     |
Start By:
- Remove the hydraulic and steering piston pump. Refer to Disassembly and Assembly, "Piston Pump (Hydraulic and Steering) - Remove".
- Remove the all wheel drive piston pump. Refer to Disassembly and Assembly, "Piston Pump (All Wheel Drive) - Remove".
- Remove the gear pump. Refer to Disassembly and Assembly, "Gear Pump (Transmission Charging and Scavenge) - Remove".
- Remove the fan pump. Refer to Disassembly and Assembly, "Piston Pump (Fan Drive) - Remove".
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. |
At operating temperature, the engine coolant is hot and under pressure. Steam can cause personal injury. Check the coolant level only after the engine has been stopped and the fill cap is cool enough to touch with your bare hand. Remove the fill cap slowly to relieve pressure. Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury. |
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Put identification marks on all hoses, on all hose assemblies, on all harness assemblies, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
- Disconnect cable assemblies (1) and (2) .
Illustration 1 | g01382579 |
- Remove bolts (3) and remove cover (4) .
- Remove clips (5) .
Illustration 2 | g01382617 |
Valve (10) is shown in the OPEN position. |
- Move valve (10) to the CLOSED position. Disconnect tube assembly (7) .
- Disconnect hoses (6) and (11) from the engine.
- Loosen clamp (8) and disconnect tube assembly (9) from the engine.
- Disconnect harness assemblies (16) and disconnect harness assembly (17) .
Illustration 3 | g01382583 |
- Remove belt (15). Refer to Operation and Maintenance Manual, "Belts - Replace"
- Remove bolts (14) and remove bracket (13). Reposition air conditioner compressor (12) out of the way.
- Disconnect tube assemblies (18) from the engine.
Illustration 4 | g01382628 |
- Disconnect hose assembly (19) .
- Remove clamp (20) .
- Remove clamp (25) .
Illustration 5 | g01382635 |
- Loosen clamps (21) on each end of tube assembly (22). Remove tube assembly (22) .
- Remove clip (23) and reposition tube assemblies (24) out of the way.
- Remove clip (26) .
- Loosen bolt (27) and disconnect harness assembly (28). Reposition harness assembly (28) out of the way.
Illustration 6 | g01382894 |
- Remove clips (29) .
- Disconnect cable assemblies (30) .
- Disconnect cable assemblies (31) .
- Remove cover (32) and disconnect harness assembly (33) .
- Remove bolts (35) and reposition hose assembly (34) out of the way.
Illustration 7 | g01382928 |
- Attach Tooling (A) and a suitable lifting device to engine (36). The weight of engine (36) is approximately 1089 kg (2400 lb).
Illustration 8 | g01382933 |
- Disconnect hose assembly (37) .
Illustration 9 | g01382947 |
- Remove bolts (38) .
- Remove the remaining bolts (38) that are underneath the machine.
Illustration 10 | g01382952 |
- Remove bolts (39). Remove elbow (40) and the O-ring seal.
- Disconnect hose assembly (42) .
Illustration 11 | g01382969 |
- Remove bolts (41) .
- Use Tooling (A) and the suitable lifting device in order to remove engine (36) from the machine.