Piston Pump (Right Propel) - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
ZZ     | 6V-9511     | Face Seal Plug (1 3/16 - 12 THD)     | 3     |
6V-9832 | Cap Assembly (1 3/16 - 12 THD)     | 3     |
Start By:
- Remove the piston pump (auxiliary). Refer to Disassembly and Assembly, "Piston Pump (Auxiliary) - Remove".
- Remove the piston pump (left drag conveyor and right auger conveyor). Refer to Disassebly and Assembly, "Piston Pump (Left Drag Conveyor and Right Auger Conveyor) - Remove".
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
- Drain the oil from the pump drive into a suitable container. Refer to Operation and Maintenance Manual for the correct procedure.
- Disconnect hose assemblies (2) from piston pump (1) .
Show/hide table
Illustration 1 | g01141737 |
- Disconnect harness assemblies (3) from piston pump (1) .
Show/hide table
Illustration 2 | g01141738 |
- Attach a suitable lifting device to piston pump (1). Remove bolts (4) and remove piston pump (1) from the machine. The weight of piston pump (1) is approximately 77 kg (170 lb).
Show/hide table
Illustration 3 | g01141739 |
- Remove the O-ring seal from piston pump (1) .
Caterpillar Information System:
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Swing Drive - Assemble
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Swing Drive - Disassemble
988G Wheel Loader Power Train Output Transfer Gears - Assemble
R2900G Load Haul Dump Braking System Pressure Switch (Brake Accumulator Oil)
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Plates (Drag Pans) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Electrical Power Supply Circuit - Test
AP500F Asphalt Paver Machine Systems Footshaft - Assemble
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Piston Pump (Auxiliary) - Install
AP500F Asphalt Paver Machine Systems Footshaft - Disassemble
C15 and C18 Engines for Caterpillar Built Machines CID 0549 FMI 02 Incorrect Throttle Lock Switch inputs
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Piston Pump (Auxiliary) - Remove
3054E Engines for Caterpillar Built Machines Engine Speed - Check
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Air Cleaner
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Rotor Stub Shaft
3054E Engines for Caterpillar Built Machines Valve Depth - Inspect
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Piston Pump (Right Propel) - Install
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Swing Gear and Bearing - Remove
725 and 730 Articulated Trucks Braking System Machine Preparation for Troubleshooting
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Swing Gear and Bearing - Install
3054E Engines for Caterpillar Built Machines Turbocharger - Inspect
2005/04/11 New Software Enables Seven Different Joystick Control Patterns for Track Feller Bunchers that Are Equipped with a Felling Head {0653, 5705, 7490, 7620}
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Swivel - Remove
834H Wheel Dozer and 836H Landfill Compactor Power Train Diagnostic Code List
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Swivel - Install