Gear Pump (Fan Drive) - Disassemble
Disassembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-1861     | Retaining Ring Pliers     | 1     |
Start By:
- Remove the fan drive gear pump. Refer to Disassembly and Assembly, "Gear Pump (Fan Drive) - Remove".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times.
Note: This component is being disassembled and displayed for CLEANING PURPOSES ONLY. Many internal parts are not available for this component. Care must be taken during disassembly and assembly in order to prevent damage to unavailable parts.
- Remove nuts (1) and end cover (2) .
Show/hide table
Illustration 1 | g01139019 |
- Remove O-ring seal (3) from end cover (2) .
Show/hide table
Illustration 2 | g01139055 |
- Remove seal (4) and backup ring (5) from end cover (2) .
- Remove thrust plate (6) from housing (7) .
Show/hide table
Illustration 3 | g01139062 |
- Remove drive gear (8) and driven gear (9) from housing (7) .
Show/hide table
Illustration 4 | g01139086 |
- Remove bolts (11) and end cover (10) from housing (7) .
Show/hide table
Illustration 5 | g01139106 |
- Remove O-ring seal (12) from end cover (10) .
Show/hide table
Illustration 6 | g01139118 |
- Remove seal (13) and backup ring (14) from end cover (10) .
- Use Tooling (A) to remove retaining ring (15) and seal (16) from end cover (10) .
Show/hide table
Illustration 7 | g01139126 |
- Remove thrust plate (17) from housing (7) .
Show/hide table
Illustration 8 | g01139168 |
Caterpillar Information System:
2005/01/31 Oversized Valve Guides are Available {1104}
2005/01/31 Oversized Valve Guides are Available {1104}
2005/01/24 Damaged Lifter Bores In 3400 Series Engines Can Be Used Again {1201}
539 Knuckleboom Loader Fuel System Secondary Filter Number One - Replace
539 Knuckleboom Loader Fuel System Secondary Filter Number Two - Replace
539 Knuckleboom Loader Engine Air Filter Service Indicator - Inspect/Replace
539 Knuckleboom Loader Belts - Inspect/Adjust/Replace
539 Knuckleboom Loader Battery or Battery Cable - Inspect/Replace
539 Knuckleboom Loader Capacities (Refill)
C7 and C9 Marine Engines E059 Low Engine Coolant Level Warning
C11 and C15 Engines for Caterpillar Built Machines E058 Low Engine Coolant Level Shutdown
C11 and C15 Engines for Caterpillar Built Machines E034 Loss of Coolant Flow Shutdown
740 and 740 EJECTOR Articulated Trucks Power Train Power Train Hydraulic System
994F Wheel Loader Bucket Wear Plates - Inspect/Replace
539 Knuckleboom Loader Reference Material
C27 and C32 Engines for Caterpillar Built Machines E361 High Engine Coolant Temperature
Topcon® System Five General Hazard Information
Installing the 266-9184 Cab Heater and Mounting Kit {7304} Installing the 266-9184 Cab Heater and Mounting Kit {7304}
C9 Engine for Caterpillar Built Machines System Configuration Parameters
AP1055D and BG2455D Asphalt Pavers Engine Supplement Gear Pump (Fan Drive) - Assemble
C7 Engine for AP-1000D, AP-1055D, BG-2455D, and BG-260D Asphalt Pavers E362 Engine Overspeed
2005/04/11 A Special instruction, REHS2561, "Field Installation of the 255-7115 Equalizer Bar As " Is Available {7206}
TK741, TK751 and TK752 Track Feller Bunchers Machine Systems Piston Pump (Saw) - Remove
Oil Volumes for Track Link Assemblies {4169} Oil Volumes for Track Link Assemblies {4169}